HS logic modules: understanding the overall logic

[Warichet]

Hi,

Yet another question, about the HS internal variables and logic modules.

I've defined a HS internal variable, init at 1.
In the graphical logic editor, I put the variable to BOTH inputs of an AND gate. So I expected the result to be 1 after the reboot of the HS !

Well no .
I can't understand this . There must some external condition before it runs ? pre-requisites ? (other then download & reboot)
In other words, when does this "init at 1" take place ?

Thank you

[Gaston]

Inline comments used to be a problem. As far as I remember this has been fixed. The problem did only occur if the comment included the "|" sign.

Kind regards,
Gaston

[Warichet]

question 3): it stops the calculation of the current module. The module will be re-triggered, when anything happens to one of the input-pins.

Thank you, that's what I understood from EIB-Freak.

so far the DACOM documentation uses comments only as standalone lines starting with '#' as first character.

Yes, I noticed, but as most languages allow for in-line comments, I wondered...

(I will not call it a bug because inlne-comments are not defined to work).

What a sweet statement ... but neither are they defined "not to work".
Anyway, I'll follow the advice of the wise.

Thank you for your kind help

[Taxus]

Inline comments

First, to your question 3): it stops the calculation of the current module. The module will be re-triggered, when anything happens to one of the input-pins.

Second, to the comments: so far the DACOM documentation uses comments only as standalone lines starting with '#' as first character. Comments may work within a line, but I don't use them any more having lost some time searching the following effect (I will not call it a bug because inlne-comments are not defined to work). With HS Experte 2.1.2 the code

5004|1|0|0|1|0
5004|2|0|0|1|0 # Kommentar 1
5004|3|"a"|0|1|1 # Kommentar 2
5004|4|"b"|0|1|1
5004|5|"c"|0|1|1 # Kommentar 3

gives the module as shown in the picture added; with HS Experte 2.2 RC it gives the module as expectet. So be careful.

Greetinx, Rainer

[Warichet]

Is it allowed to put a comment on the same line as a definition or a formula, like:

5001|2|2|1|1|0  # 2 Input, 2 Output, 1 Time Var, 1 Mem Var, No Compute at Start

Normally, yes, but who knows....
I've found no example where it is written that way, so I ask.

Thank you

[Michel]

Yes, you are right. Just put the "Kommunikationsobjekt" in the Out-Box to switch e.g. a lamp.

[Warichet]

at any event on the Inputs the module is calculating/working.

Sorry, forgot to ask about the Grafisher Logikeditor ...
Suppose the output of the logic module is 1, is it sufficient to feed it directly to an Ausgangs-box i.e. just like a PB would do to light a lamp ? or do I need to specify "Befehle".
I thought the "Befehle" field is for additional commands ?

Thanks

[Warichet]

at any event on the Inputs the module is calculating/working.

OK, thanks

The module calculate/work while the HS restarts.

OK, thanks. I totally misundestood this. I though it was at initializing of the logic bloc itself

Look also here: https://knx-user-forum.de/showthread.php?t=357 (page 3)

I've read the topic several times, but mmmh, my poor knowledge of the language is a handicap.

Thank you "Magier" for helping a poor apprentice sorcerer

1) Is the logic module evaluated only once, or is it looping for ever ?

at any event on the Inputs the module is calculating/working.
Such as KNX: Event-based!

2) There is a variable EI "Die Berechnung findet innerhalb der Initialisierung statt."

The module calculate/work while the HS restarts. Look also here: https://knx-user-forum.de/showthread.php?t=357 (page 3)

[Warichet]

Hi,

I've some questions about the working of the overall logic of the logic modules.

1) Is the logic module evaluated only once, or is it looping for ever ?

2) There is a variable EI "Die Berechnung findet innerhalb der Initialisierung statt."
but don't fully undestand the meaning or use, an example would help.

3) In the 5012 line, there is a flag "Ende nach Ausführen"
does it mean that only the current line is not executed anymore after this run (but all subsequent well) or does it stop the whole logic module for ever (in which case, another question arises: how can I restart it).

Thank you