Hallo ab und zu hat mein einen Punkt da sieht man den Wald vor lauter Bäumen nicht mehr ich Glaube da steh ich gerade . Ich hab OpenHab auf einem Raspberry
B+ am laufen bekomme aber irgentwie die übergabe zum knx Bus nicht hin
Meine cfg sieht so aus :
################################ KNX Binding ##########################################
#
# KNX gateway IP address
# (optional, if serialPort or connection type 'ROUTER' is specified)
knx:ip=192.168.178.198
# KNX IP connection type. Could be either TUNNEL or ROUTER (optional, defaults to TUNNEL)
# Note: If you cannot get the ROUTER mode working (even if it claims it is connected),
# use TUNNEL mode instead with setting both the ip of the KNX gateway and the localIp.
knx:type=TUNNEL
# KNX gateway port (optional, defaults to 3671)
#knx
ort=
# Local endpoint to specify the multicast interface, no port is used (optional)
#knx:localIp=192.168.178.199
# Serial port of FT1.2 KNX interface (ignored, if ip is specified)
# Valid values are e.g. COM1 for Windows and /dev/ttyS0 or /dev/ttyUSB0 for Linux
#knx:serialPort=
# Pause in milliseconds between two read requests on the KNX bus during
# initialization (optional, defaults to 50)
#knx
ause=
# Timeout in milliseconds to wait for a response from the KNX bus (optional,
# defaults to 10000)
#knx:timeout
# Number of read retries while initialization items from the KNX bus (optional,
# defaults to 3)
#knx:readRetries
# Seconds between connect retries when KNX link has been lost
# 0 means never retry, it will only reconnect on next write or read request
# Note: without periodic retries all events will be lost up to the next read/write
# request
# (optional, default is 0)
#knx:autoReconnectPeriod=30
Sollte ja passen
beim start bekomme ich die meldung das der tunnel zu dem IP Router läuft
bekomme aber nichts auf den Bus
B+ am laufen bekomme aber irgentwie die übergabe zum knx Bus nicht hin

Meine cfg sieht so aus :
################################ KNX Binding ##########################################
#
# KNX gateway IP address
# (optional, if serialPort or connection type 'ROUTER' is specified)
knx:ip=192.168.178.198
# KNX IP connection type. Could be either TUNNEL or ROUTER (optional, defaults to TUNNEL)
# Note: If you cannot get the ROUTER mode working (even if it claims it is connected),
# use TUNNEL mode instead with setting both the ip of the KNX gateway and the localIp.
knx:type=TUNNEL
# KNX gateway port (optional, defaults to 3671)
#knx

# Local endpoint to specify the multicast interface, no port is used (optional)
#knx:localIp=192.168.178.199
# Serial port of FT1.2 KNX interface (ignored, if ip is specified)
# Valid values are e.g. COM1 for Windows and /dev/ttyS0 or /dev/ttyUSB0 for Linux
#knx:serialPort=
# Pause in milliseconds between two read requests on the KNX bus during
# initialization (optional, defaults to 50)
#knx

# Timeout in milliseconds to wait for a response from the KNX bus (optional,
# defaults to 10000)
#knx:timeout
# Number of read retries while initialization items from the KNX bus (optional,
# defaults to 3)
#knx:readRetries
# Seconds between connect retries when KNX link has been lost
# 0 means never retry, it will only reconnect on next write or read request
# Note: without periodic retries all events will be lost up to the next read/write
# request
# (optional, default is 0)
#knx:autoReconnectPeriod=30
Sollte ja passen
beim start bekomme ich die meldung das der tunnel zu dem IP Router läuft
bekomme aber nichts auf den Bus
Kommentar