LBS Tasmota (14331)

[Opelpower]

Prüf mal bitte das GA in echt 😅

Also, dies musst du mir jetzt echt mal erklären.
Eines Vorweg: Mit einer echten GA funktioniert es!?
Und mit einer internen geht es auch.

Im Grunde funktioniert der Baustein.
Der Zähler vom Ausgang A1 bleibt allerdings bei mir immer auf 0, wenn ich ihn im Experte beobachtet.
Stoppe und Starte ich die Beobachtung Neu, zeigt er auch den richtigen Ausgangsstatus.

Dachte eigentlich man könnte sich auf die interne Diagnose verlassen.

[derPaul]

Muss jetzt erst die Kinder baden..............

Das hab ich aufgegeben ... sind danach eh immer wieder direkt schmutzig ... 😂

[Opelpower]

Muss jetzt erst die Kinder baden..............

[derPaul]

Prüf mal bitte das GA in echt 😅

[Opelpower]

0 bringt nichts ... er checkt auf beide Keys "POWER" und "POWERx" (wobei X dann die Channel ID ist) ...
Ich gehe ganz fest davon aus das bei ufkel das damit behoben ist. Wieso er das bei dir nicht macht ... gute Frage.

Guckst du nur im Experten in der Live Ansicht oder auch wirklich die GA in die du das schreiben willst?

Ich gucke momentan immer im Experten in der Live Ansicht.

Habe den Eingang + Triggereingang jetzt mehrmals verändert, aber bei Status Ausgang bleibt immer die 1. tasmota.png

[derPaul]

Gerade ausprobiert, aber leider ändert sich immer noch nichts am Ausgang 1.
Habe es einfach mal mit Channel 0 und 1 ausprobiert.

Unter Exceptions wird bei mir nichts angezeigt mit Tasmota

0 bringt nichts ... er checkt auf beide Keys "POWER" und "POWERx" (wobei X dann die Channel ID ist) ...
Ich gehe ganz fest davon aus das bei ufkel das damit behoben ist. Wieso er das bei dir nicht macht ... gute Frage.

Guckst du nur im Experten in der Live Ansicht oder auch wirklich die GA in die du das schreiben willst?

[Opelpower]

Gerade ausprobiert, aber leider ändert sich immer noch nichts am Ausgang 1.
Habe es einfach mal mit Channel 0 und 1 ausprobiert.

Unter Exceptions wird bei mir nichts angezeigt mit Tasmota

[derPaul]

V0.3
- Channel Ausgang angepasst


Bitte mit der V0.3 noch mal probieren ... :-)

[derPaul]

Ich denke Du hast Recht.

12:19:31.986 MQT: stat/tasmota_F377FC/RESULT = {"Time":"2021-12-18T12:19:31","Uptime":"0T00:01:05","UptimeSec":65, "Heap":21,"SleepMode":"Dynamic","Sleep":50,"LoadAv g":19,"MqttCount":1,"POWER1":"ON","POWER2":"OFF"," Wifi":{"AP":1,"SSId":"UFK2","BSSId":"F0:9F:C2:7A:2 8:7B","Channel":6,"Mode":"11n","RSSI":78,"Signal":-61,"LinkCount":1,"Downtime":"0T00:00:04"}}
12:19:36.238 MQT: stat/tasmota_F377FC/RESULT = {"POWER1":"ON"}
12:19:36.243 MQT: stat/tasmota_F377FC/POWER1 = ON
12:19:37.091 MQT: stat/tasmota_F377FC/RESULT = {"Time":"2021-12-18T12:19:37","Uptime":"0T00:01:11","UptimeSec":71, "Heap":21,"SleepMode":"Dynamic","Sleep":50,"LoadAv g":19,"MqttCount":1,"POWER1":"ON","POWER2":"OFF"," Wifi":{"AP":1,"SSId":"UFK2","BSSId":"F0:9F:C2:7A:2 8:7B","Channel":6,"Mode":"11n","RSSI":78,"Signal":-61,"LinkCount":1,"Downtime":"0T00:00:04"}}
12:19:38.542 MQT: stat/tasmota_F377FC/RESULT = {"POWER1":"ON"}
12:19:38.547 MQT: stat/tasmota_F377FC/POWER1 = ON
12:19:42.195 MQT: stat/tasmota_F377FC/RESULT = {"Time":"2021-12-18T12:19:42","Uptime":"0T00:01:16","UptimeSec":76, "Heap":21,"SleepMode":"Dynamic","Sleep":50,"LoadAv g":19,"MqttCount":1,"POWER1":"ON","POWER2":"OFF"," Wifi":{"AP":1,"SSId":"UFK2","BSSId":"F0:9F:C2:7A:2 8:7B","Channel":6,"Mode":"11n","RSSI":78,"Signal":-61,"LinkCount":1,"Downtime":"0T00:00:04"}}
12:19:47.302 MQT: stat/tasmota_F377FC/RESULT = {"Time":"2021-12-18T12:19:47","Uptime":"0T00:01:21","UptimeSec":81, "Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAv g":19,"MqttCount":1,"POWER1":"ON","POWER2":"OFF"," Wifi":{"AP":1,"SSId":"UFK2","BSSId":"F0:9F:C2:7A:2 8:7B","Channel":6,"Mode":"11n","RSSI":78,"Signal":-61,"LinkCount":1,"Downtime":"0T00:00:04"}}
12:19:50.456 MQT: stat/tasmota_F377FC/RESULT = {"POWER1":"OFF"}
12:19:50.460 MQT: stat/tasmota_F377FC/POWER1 = OFF
12:19:52.361 MQT: stat/tasmota_F377FC/RESULT = {"Time":"2021-12-18T12:19:52","Uptime":"0T00:01:26","UptimeSec":86, "Heap":21,"SleepMode":"Dynamic","Sleep":50,"LoadAv g":19,"MqttCount":1,"POWER1":"OFF","POWER2":"OFF", "Wifi":{"AP":1,"SSId":"UFK2","BSSId":"F0:9F:C2:7A: 28:7B","Channel":6,"Mode":"11n","RSSI":76,"Signal" :-62,"LinkCount":1,"Downtime":"0T00:00:04"}}
12:19:57.425 MQT: stat/tasmota_F377FC/RESULT = {"Time":"2021-12-18T12:19:57","Uptime":"0T00:01:31"

Die Keys heißen bei mir POWER1 und POWER2. Wenn die die Exception recht verstehe, erwartet der LBS den Key POWER:

Screenshot 2021-12-18 at 12.21.43.png

ahhh perfekt ... ja Channel hab ich gerade eingebaut, aber nicht bei der Ausgabe ... sekunde das hol ich nach ...

[ufkel]

Ah stimmt hier könnt das an den Channels liegen ... da wäre das mal sehr Interessant was der Befehl bei dir ausgibt ... kannst du mir den mal eben zukommen lassen ?

Ich denke Du hast Recht.

12:19:31.986 MQT: stat/tasmota_F377FC/RESULT = {"Time":"2021-12-18T12:19:31","Uptime":"0T00:01:05","UptimeSec":65, "Heap":21,"SleepMode":"Dynamic","Sleep":50,"LoadAv g":19,"MqttCount":1,"POWER1":"ON","POWER2":"OFF"," Wifi":{"AP":1,"SSId":"UFK2","BSSId":"F0:9F:C2:7A:2 8:7B","Channel":6,"Mode":"11n","RSSI":78,"Signal":-61,"LinkCount":1,"Downtime":"0T00:00:04"}}
12:19:36.238 MQT: stat/tasmota_F377FC/RESULT = {"POWER1":"ON"}
12:19:36.243 MQT: stat/tasmota_F377FC/POWER1 = ON
12:19:37.091 MQT: stat/tasmota_F377FC/RESULT = {"Time":"2021-12-18T12:19:37","Uptime":"0T00:01:11","UptimeSec":71, "Heap":21,"SleepMode":"Dynamic","Sleep":50,"LoadAv g":19,"MqttCount":1,"POWER1":"ON","POWER2":"OFF"," Wifi":{"AP":1,"SSId":"UFK2","BSSId":"F0:9F:C2:7A:2 8:7B","Channel":6,"Mode":"11n","RSSI":78,"Signal":-61,"LinkCount":1,"Downtime":"0T00:00:04"}}
12:19:38.542 MQT: stat/tasmota_F377FC/RESULT = {"POWER1":"ON"}
12:19:38.547 MQT: stat/tasmota_F377FC/POWER1 = ON
12:19:42.195 MQT: stat/tasmota_F377FC/RESULT = {"Time":"2021-12-18T12:19:42","Uptime":"0T00:01:16","UptimeSec":76, "Heap":21,"SleepMode":"Dynamic","Sleep":50,"LoadAv g":19,"MqttCount":1,"POWER1":"ON","POWER2":"OFF"," Wifi":{"AP":1,"SSId":"UFK2","BSSId":"F0:9F:C2:7A:2 8:7B","Channel":6,"Mode":"11n","RSSI":78,"Signal":-61,"LinkCount":1,"Downtime":"0T00:00:04"}}
12:19:47.302 MQT: stat/tasmota_F377FC/RESULT = {"Time":"2021-12-18T12:19:47","Uptime":"0T00:01:21","UptimeSec":81, "Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAv g":19,"MqttCount":1,"POWER1":"ON","POWER2":"OFF"," Wifi":{"AP":1,"SSId":"UFK2","BSSId":"F0:9F:C2:7A:2 8:7B","Channel":6,"Mode":"11n","RSSI":78,"Signal":-61,"LinkCount":1,"Downtime":"0T00:00:04"}}
12:19:50.456 MQT: stat/tasmota_F377FC/RESULT = {"POWER1":"OFF"}
12:19:50.460 MQT: stat/tasmota_F377FC/POWER1 = OFF
12:19:52.361 MQT: stat/tasmota_F377FC/RESULT = {"Time":"2021-12-18T12:19:52","Uptime":"0T00:01:26","UptimeSec":86, "Heap":21,"SleepMode":"Dynamic","Sleep":50,"LoadAv g":19,"MqttCount":1,"POWER1":"OFF","POWER2":"OFF", "Wifi":{"AP":1,"SSId":"UFK2","BSSId":"F0:9F:C2:7A: 28:7B","Channel":6,"Mode":"11n","RSSI":76,"Signal" :-62,"LinkCount":1,"Downtime":"0T00:00:04"}}
12:19:57.425 MQT: stat/tasmota_F377FC/RESULT = {"Time":"2021-12-18T12:19:57","Uptime":"0T00:01:31"

Die Keys heißen bei mir POWER1 und POWER2. Wenn die die Exception recht verstehe, erwartet der LBS den Key POWER:

Screenshot 2021-12-18 at 12.21.43.png

[derPaul]

V0.2
- Channel Auswahl hinzugefügt

Mit E8 kann man jetzt den Channel angeben sollte das Geräte mehrere haben.

[derPaul]

Bei Tasmota AUS

{"Time":"2021-12-18T11:42:23","Uptime":"0T00:32:45","UptimeSec":196 5,"Heap":21,"SleepMode":"Dynamic","Sleep":50,"Load Avg":19,"MqttCount":0,"POWER":"OFF","Wifi":{"AP":1 ,"SSId":"FRITZ!Box Fon WLAN 7490","BSSId":"'*******","Channel":11,"RSSI":60,"Signal":-70,"LinkCount":1,"Downtime":"0T00:00:05"}} 

Bei Tasmota AN

{"Time":"2021-12-18T11:43:48","Uptime":"0T00:34:10","UptimeSec":205 0,"Heap":21,"SleepMode":"Dynamic","Sleep":50,"Load Avg":19,"MqttCount":0,"POWER":"ON","Wifi":{"AP":1, "SSId":"FRITZ!Box Fon WLAN 7490","BSSId":"********","Channel":11,"RSSI":56,"Signal":-72,"LinkCount":1,"Downtime":"0T00:00:05"}} 

Danke, da is der richtige Wert enthalten, komisch ... magst du mal gucken ob es ne Exception vorher gibt? Auf der Debug Seite vom HS

[derPaul]

Achtung die Tasmota Knx sind nicht mit ETS5 kompatibel? Sie müssen den Thelsing Knx-Github verwenden

We don't talk about the KNX Stack Communication for Tasmota here. This LBS is for HTTP Communication.

[richardpub]

kk

[Opelpower]

Bei Tasmota AUS

{"Time":"2021-12-18T11:42:23","Uptime":"0T00:32:45","UptimeSec":196 5,"Heap":21,"SleepMode":"Dynamic","Sleep":50,"Load Avg":19,"MqttCount":0,"POWER":"OFF","Wifi":{"AP":1 ,"SSId":"FRITZ!Box Fon WLAN 7490","BSSId":"'*******","Channel":11,"RSSI":60,"Signal":-70,"LinkCount":1,"Downtime":"0T00:00:05"}} 

Bei Tasmota AN

{"Time":"2021-12-18T11:43:48","Uptime":"0T00:34:10","UptimeSec":205 0,"Heap":21,"SleepMode":"Dynamic","Sleep":50,"Load Avg":19,"MqttCount":0,"POWER":"ON","Wifi":{"AP":1, "SSId":"FRITZ!Box Fon WLAN 7490","BSSId":"********","Channel":11,"RSSI":56,"Signal":-72,"LinkCount":1,"Downtime":"0T00:00:05"}}