Hallo,
den Verdacht hatte ich auch, v.a. da ich auch beim Example-Sketch einen Fehler hatte[1].
Aber:
Ich habe vor ca. einem Monat alles installiert (und auch erstmalig heruntergeladen).
Der Code von Github ist 7 Monate nicht geändert und die Lib von der Bosch-Seite ist von September (1.4.7.1).
Ich habe ein Issue aufgemacht:
https://github.com/BoschSensortec/BS...rary/issues/32
Gruß,
Hendrik
[1] Das liegt in meinen Augen aber am Beispiel-Sketch, siehe:
https://github.com/BoschSensortec/BS...rary/issues/27
Funktioniert der bei dir?
-
Vermutlich passt der Coder der Lib nicht zur Binärdatei die zu von der Bosch-Seite runtergeladen hast. Ich würde einfach mal probieren beiden auf den aktuellen Stand zu aktualisieren.Einen Kommentar schreiben:
-
Hallo Thomas,
vielen Dank.
Ich habe jetzt sehr lange gebraucht:
1) i2c Adresse habe ich mit einem i2c Scanner-Sketch herausgefunden (0x77)
2) wire.pin() hat nicht funktioniert
3) wire.begin(0, 5) vor iaqSensor.begin funktioniert (keine Änderung in bsec.cpp nötig)
4) iaqSensor.begin(BME680_I2C_ADDR_PRIMARY,Wire); funktioniert nicht. iaqSensor.begin(0x77,Wire); schon
5) Ich bekomme jetzt einen BSEC error code -34
Dazu habe ich dies gefunden:
Kannst du damit etwas anfangen?3.3.3.1 BSEC_E_CONFIG_VERSIONMISMATCH
Possiblereasons:
· General description: BSEC_E_CONFIG_VERSIONMISMATCH
· Version mentioned in the configuration string or state string passed to bsec_set_configuration() or bsec_setstate(),respectively, does not match with the currentversion. Correction methods:
· Obtain a compatible string.
· Acallto bsec_get_version() would give the current version information.
Gruß&Danke,
HendrikZuletzt geändert von henfri; 11.11.2018, 15:26.Einen Kommentar schreiben:
-
Es sollte reichen wenn du Wire.pins(sda, scl) in setup() vor "iaqSensor.begin(BME680_I2C_ADDR_SECONDARY, Wire);" aufrufst. Alternativ kannst du auch das Wire.begin hier ändern https://github.com/BoschSensortec/BS.../bsec.cpp#L102
Die Adresse muss bei iaqSensor.begin(BME680_I2C_ADDR_SECONDARY, Wire); musst du ggf. auch noch anpassen. Je nachdem welche Adresse dein BME680 Modul verwendet.Einen Kommentar schreiben:
-
Hallo,
danke.
Ich finde Wire.begin im Code aktuell garnicht.
Ich verstehe obiges so, dass man damit Wire initialisiert. Oder kann ich diesen Aufruf einfach in setup() in deinem Code aufrufen?
Gruß,
HendrikEinen Kommentar schreiben:
-
Sollte man ändern können. Nach https://learn.sparkfun.com/tutorials...-arduino-addon :
Wire - The ESP8266 should work with any I2C sensor you can throw at it - just use the same Wire API calls you're used to. There are a few differences:
Pin definition: The ESP2866 doesn't actually have any hardware I2C pins - those labeled on the Thing are the default, but you can actually use any two pins as SDA and SCL. Calling Wire.begin() will assume pins 2 and 14 are SDA and SCL, but you can manually set them to any other pin by calling Wire.begin([SDA], [SCL]).Einen Kommentar schreiben:
-
Super, vielen Dank!
Noch eine Frage:
An meinem ESP-Bord ist der Anschluss, der üblicherweise für I2C verwendet wird schon mit einem Taster belegt.
Weißt du, ob es möglich ist die GPIO Pins für I2C zu ändern (entweder in deinem Code oder in der BME-Lib)?
Gruß,
HendrikEinen Kommentar schreiben:
-
Das Problem sollte schon behoben sein. Habe die nötige Änderung am 27.10. eingecheckt.Einen Kommentar schreiben:
-
Hallo,
hattest du vor das oben gezeigte Problem mit der ETS zu beheben?
Oder sollte ich ein Update der ETS machen? Wobei ich es so verstanden hab, dass meine ETS eher zu neu ist (?)
Gruß,
HendrikEinen Kommentar schreiben:
-
Ich habe die ganzen git-Repositories zusammengefasst. Der Code ist jetzt unter https://github.com/thelsing/knx zu finden. Git pull produziert auf den alten Repositories wahrscheinlich nun Unsinn.Einen Kommentar schreiben:
-
Hallo,
das nächste log kommt gerne als XML.
Ich habe noch die ETS 5.0.5.
Gruß,
HendrikEinen Kommentar schreiben:
-
Welche ETS Version nutzt du? ETS fragt nach der Beschreibung einer Eigenschaft die ich noch nicht implementiert habe. Ich brauchte die bisher nicht. Hab die Beschreibung nun ergänzt. Die Logs lassen sich einfacher lesen, wenn du einfach die Telegramme einfach als xml speicherst. Dann kann ich die Datei in ETS laden und dort anschauen.Einen Kommentar schreiben:
-
Hallo,
es war alles richtig, aber weil noch kein BME angeschlossen ist, ging der code immer in die Funktion ErrorLED.
Ich habe den Part auskommentiert und konnte nun die WPS Verbindung starten und eine Physikalische Adresse programmieren können.
Das Programmieren der GAs/des Applikatinosprogramms schlägt aber fehl:
Hast du eine Idee, was hier schief geht?Code:# Zeit Dienst Flags Prio Quell-Adresse Quell-Name Ziel-Adresse Ziel-Name Rout Typ DPT Info 48 2018-10-27 10:55:44.070 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_Connect 49 2018-10-27 10:55:44.070 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_Connect 50 2018-10-27 10:55:44.090 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 DeviceDescriptorRead (S=0) DescriptorType=0 51 2018-10-27 10:55:44.091 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 DeviceDescriptorRead (S=0) DescriptorType=0 52 2018-10-27 10:55:44.096 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=0) 53 2018-10-27 10:55:44.130 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 DeviceDescriptorResponse (S=0) DescriptorType=0, DescriptorData=57 B0 54 2018-10-27 10:55:44.131 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=0) 55 2018-10-27 10:55:44.131 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=0) 56 2018-10-27 10:55:44.151 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 AuthorizeRequest (S=1) 00 FF FF FF FF 57 2018-10-27 10:55:44.151 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 AuthorizeRequest (S=1) 00 FF FF FF FF 58 2018-10-27 10:55:44.156 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=1) 59 2018-10-27 10:55:44.177 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 AuthorizeResponse (S=1) $00 60 2018-10-27 10:55:44.178 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=1) 61 2018-10-27 10:55:44.178 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=1) 62 2018-10-27 10:55:44.198 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyDescriptionRead (S=2) 02 17 00 63 2018-10-27 10:55:44.198 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyDescriptionRead (S=2) 02 17 00 64 2018-10-27 10:55:44.204 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=2) 65 2018-10-27 10:55:44.223 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyDescriptionResponse (S=2) 02 17 01 12 00 FE 30 66 2018-10-27 10:55:44.224 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=2) 67 2018-10-27 10:55:44.224 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=2) 68 2018-10-27 10:55:44.245 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=3) ObjectIndex=0, PropertyId=11, Count=1, StartIndex=1 69 2018-10-27 10:55:44.245 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=3) ObjectIndex=0, PropertyId=11, Count=1, StartIndex=1 70 2018-10-27 10:55:44.267 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=3) 71 2018-10-27 10:55:44.271 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=3) ObjectIndex=0, PropertyId=11, Count=1, StartIndex=1, Data=00 00 00 00 01 00 72 2018-10-27 10:55:44.272 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=3) 73 2018-10-27 10:55:44.272 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=3) 74 2018-10-27 10:55:44.291 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=4) ObjectIndex=0, PropertyId=56, Count=1, StartIndex=1 75 2018-10-27 10:55:44.291 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=4) ObjectIndex=0, PropertyId=56, Count=1, StartIndex=1 76 2018-10-27 10:55:44.297 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=4) 77 2018-10-27 10:55:44.316 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=4) ObjectIndex=0, PropertyId=56, Count=1, StartIndex=1, Data=00 0F 78 2018-10-27 10:55:44.317 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=4) 79 2018-10-27 10:55:44.317 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=4) 80 2018-10-27 10:55:44.338 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=5) ObjectIndex=0, PropertyId=12, Count=1, StartIndex=1 81 2018-10-27 10:55:44.338 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=5) ObjectIndex=0, PropertyId=12, Count=1, StartIndex=1 82 2018-10-27 10:55:44.357 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=5) 83 2018-10-27 10:55:44.364 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=5) ObjectIndex=0, PropertyId=12, Count=1, StartIndex=1, Data=00 FA 84 2018-10-27 10:55:44.365 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=5) 85 2018-10-27 10:55:44.365 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=5) 86 2018-10-27 10:55:44.386 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=6) ObjectIndex=0, PropertyId=25, Count=1, StartIndex=1 87 2018-10-27 10:55:44.386 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=6) ObjectIndex=0, PropertyId=25, Count=1, StartIndex=1 88 2018-10-27 10:55:44.392 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=6) 89 2018-10-27 10:55:44.412 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=6) ObjectIndex=0, PropertyId=25, Count=1, StartIndex=1, Data=00 00 90 2018-10-27 10:55:44.413 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=6) 91 2018-10-27 10:55:44.413 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=6) 92 2018-10-27 10:55:44.433 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=7) ObjectIndex=0, PropertyId=78, Count=1, StartIndex=1 93 2018-10-27 10:55:44.433 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=7) ObjectIndex=0, PropertyId=78, Count=1, StartIndex=1 94 2018-10-27 10:55:44.436 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=7) 95 2018-10-27 10:55:44.457 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=7) ObjectIndex=0, PropertyId=78, Count=1, StartIndex=1, Data=00 00 00 00 00 00 96 2018-10-27 10:55:44.458 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=7) 97 2018-10-27 10:55:44.458 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=7) 98 2018-10-27 10:55:44.478 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=8) ObjectIndex=0, PropertyId=15, Count=1, StartIndex=1 99 2018-10-27 10:55:44.478 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=8) ObjectIndex=0, PropertyId=15, Count=1, StartIndex=1 100 2018-10-27 10:55:44.482 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=8) 101 2018-10-27 10:55:44.502 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=8) ObjectIndex=0, PropertyId=15, Count=1, StartIndex=1, Data=00 00 00 00 00 00 00 00 00 00 102 2018-10-27 10:55:44.503 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=8) 103 2018-10-27 10:55:44.503 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=8) 104 2018-10-27 10:55:44.538 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=9) ObjectIndex=5, PropertyId=5, Count=1, StartIndex=1, Data=04 00 00 00 00 00 00 00 00 00 105 2018-10-27 10:55:44.538 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=9) ObjectIndex=5, PropertyId=5, Count=1, StartIndex=1, Data=04 00 00 00 00 00 00 00 00 00 106 2018-10-27 10:55:44.545 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=9) 107 2018-10-27 10:55:44.565 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=9) ObjectIndex=5, PropertyId=5, Count=0, StartIndex=1 108 2018-10-27 10:55:44.566 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=9) 109 2018-10-27 10:55:44.566 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=9) 110 2018-10-27 10:55:44.588 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=10) ObjectIndex=4, PropertyId=5, Count=1, StartIndex=1, Data=04 00 00 00 00 00 00 00 00 00 111 2018-10-27 10:55:44.588 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=10) ObjectIndex=4, PropertyId=5, Count=1, StartIndex=1, Data=04 00 00 00 00 00 00 00 00 00 112 2018-10-27 10:55:44.597 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=10) 113 2018-10-27 10:55:44.625 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=10) ObjectIndex=4, PropertyId=5, Count=1, StartIndex=1, Data=$00 114 2018-10-27 10:55:44.626 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=10) 115 2018-10-27 10:55:44.626 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=10) 116 2018-10-27 10:55:44.646 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=11) ObjectIndex=3, PropertyId=5, Count=1, StartIndex=1, Data=04 00 00 00 00 00 00 00 00 00 117 2018-10-27 10:55:44.646 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=11) ObjectIndex=3, PropertyId=5, Count=1, StartIndex=1, Data=04 00 00 00 00 00 00 00 00 00 118 2018-10-27 10:55:44.657 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=11) 119 2018-10-27 10:55:44.674 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=11) ObjectIndex=3, PropertyId=5, Count=1, StartIndex=1, Data=$00 120 2018-10-27 10:55:44.675 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=11) 121 2018-10-27 10:55:44.675 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=11) 123 2018-10-27 10:55:44.695 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=12) ObjectIndex=2, PropertyId=5, Count=1, StartIndex=1, Data=04 00 00 00 00 00 00 00 00 00 124 2018-10-27 10:55:44.695 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=12) ObjectIndex=2, PropertyId=5, Count=1, StartIndex=1, Data=04 00 00 00 00 00 00 00 00 00 125 2018-10-27 10:55:44.700 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=12) 126 2018-10-27 10:55:44.728 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=12) ObjectIndex=2, PropertyId=5, Count=1, StartIndex=1, Data=$00 127 2018-10-27 10:55:44.729 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=12) 128 2018-10-27 10:55:44.729 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=12) 129 2018-10-27 10:55:44.750 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=13) ObjectIndex=1, PropertyId=5, Count=1, StartIndex=1, Data=04 00 00 00 00 00 00 00 00 00 130 2018-10-27 10:55:44.750 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=13) ObjectIndex=1, PropertyId=5, Count=1, StartIndex=1, Data=04 00 00 00 00 00 00 00 00 00 131 2018-10-27 10:55:44.754 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=13) 132 2018-10-27 10:55:44.792 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=13) ObjectIndex=1, PropertyId=5, Count=1, StartIndex=1, Data=$00 133 2018-10-27 10:55:44.793 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=13) 134 2018-10-27 10:55:44.793 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=13) 135 2018-10-27 10:55:44.828 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=14) ObjectIndex=4, PropertyId=5, Count=1, StartIndex=1, Data=01 00 00 00 00 00 00 00 00 00 136 2018-10-27 10:55:44.828 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=14) ObjectIndex=4, PropertyId=5, Count=1, StartIndex=1, Data=01 00 00 00 00 00 00 00 00 00 137 2018-10-27 10:55:44.832 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=14) 138 2018-10-27 10:55:44.852 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=14) ObjectIndex=4, PropertyId=5, Count=1, StartIndex=1, Data=$02 139 2018-10-27 10:55:44.853 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=14) 140 2018-10-27 10:55:44.853 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=14) 141 2018-10-27 10:55:44.874 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=15) ObjectIndex=4, PropertyId=5, Count=1, StartIndex=1, Data=03 0B 00 00 00 04 00 00 00 00 142 2018-10-27 10:55:44.874 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=15) ObjectIndex=4, PropertyId=5, Count=1, StartIndex=1, Data=03 0B 00 00 00 04 00 00 00 00 143 2018-10-27 10:55:44.878 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=15) 144 2018-10-27 10:55:44.899 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=15) ObjectIndex=4, PropertyId=5, Count=1, StartIndex=1, Data=$02 145 2018-10-27 10:55:44.900 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=15) 146 2018-10-27 10:55:44.901 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=15) 147 2018-10-27 10:55:44.921 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=0) ObjectIndex=3, PropertyId=5, Count=1, StartIndex=1, Data=01 00 00 00 00 00 00 00 00 00 148 2018-10-27 10:55:44.921 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=0) ObjectIndex=3, PropertyId=5, Count=1, StartIndex=1, Data=01 00 00 00 00 00 00 00 00 00 149 2018-10-27 10:55:44.928 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=0) 150 2018-10-27 10:55:44.947 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=0) ObjectIndex=3, PropertyId=5, Count=1, StartIndex=1, Data=$02 151 2018-10-27 10:55:44.948 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=0) 152 2018-10-27 10:55:44.948 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=0) 153 2018-10-27 10:55:44.978 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=1) ObjectIndex=3, PropertyId=5, Count=1, StartIndex=1, Data=03 0B 00 00 00 16 00 00 00 00 154 2018-10-27 10:55:44.979 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=1) ObjectIndex=3, PropertyId=5, Count=1, StartIndex=1, Data=03 0B 00 00 00 16 00 00 00 00 155 2018-10-27 10:55:44.982 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=1) 156 2018-10-27 10:55:45.010 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=1) ObjectIndex=3, PropertyId=5, Count=1, StartIndex=1, Data=$02 157 2018-10-27 10:55:45.012 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=1) 158 2018-10-27 10:55:45.012 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=1) 159 2018-10-27 10:55:45.032 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=2) ObjectIndex=1, PropertyId=5, Count=1, StartIndex=1, Data=01 00 00 00 00 00 00 00 00 00 160 2018-10-27 10:55:45.032 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=2) ObjectIndex=1, PropertyId=5, Count=1, StartIndex=1, Data=01 00 00 00 00 00 00 00 00 00 161 2018-10-27 10:55:45.036 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=2) 162 2018-10-27 10:55:45.057 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=2) ObjectIndex=1, PropertyId=5, Count=1, StartIndex=1, Data=$02 163 2018-10-27 10:55:45.057 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=2) 164 2018-10-27 10:55:45.057 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=2) 165 2018-10-27 10:55:45.078 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=3) ObjectIndex=1, PropertyId=5, Count=1, StartIndex=1, Data=03 0B 00 00 00 02 00 00 00 00 166 2018-10-27 10:55:45.078 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=3) ObjectIndex=1, PropertyId=5, Count=1, StartIndex=1, Data=03 0B 00 00 00 02 00 00 00 00 167 2018-10-27 10:55:45.082 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=3) 168 2018-10-27 10:55:45.113 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=3) ObjectIndex=1, PropertyId=5, Count=1, StartIndex=1, Data=$02 169 2018-10-27 10:55:45.114 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=3) 170 2018-10-27 10:55:45.114 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=3) 171 2018-10-27 10:55:45.135 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=4) ObjectIndex=2, PropertyId=5, Count=1, StartIndex=1, Data=01 00 00 00 00 00 00 00 00 00 172 2018-10-27 10:55:45.135 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=4) ObjectIndex=2, PropertyId=5, Count=1, StartIndex=1, Data=01 00 00 00 00 00 00 00 00 00 173 2018-10-27 10:55:45.140 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=4) 174 2018-10-27 10:55:45.161 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=4) ObjectIndex=2, PropertyId=5, Count=1, StartIndex=1, Data=$02 175 2018-10-27 10:55:45.162 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=4) 176 2018-10-27 10:55:45.162 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=4) 177 2018-10-27 10:55:45.183 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=5) ObjectIndex=2, PropertyId=5, Count=1, StartIndex=1, Data=03 0B 00 00 00 02 00 00 00 00 178 2018-10-27 10:55:45.201 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=5) ObjectIndex=2, PropertyId=5, Count=1, StartIndex=1, Data=03 0B 00 00 00 02 00 00 00 00 179 2018-10-27 10:55:45.201 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=5) 180 2018-10-27 10:55:45.210 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=5) ObjectIndex=2, PropertyId=5, Count=1, StartIndex=1, Data=$02 181 2018-10-27 10:55:45.211 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=5) 182 2018-10-27 10:55:45.211 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=5) 183 2018-10-27 10:55:45.231 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=6) ObjectIndex=4, PropertyId=7, Count=1, StartIndex=1 184 2018-10-27 10:55:45.231 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=6) ObjectIndex=4, PropertyId=7, Count=1, StartIndex=1 185 2018-10-27 10:55:45.237 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=6) 186 2018-10-27 10:55:45.259 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=6) ObjectIndex=4, PropertyId=7, Count=1, StartIndex=1, Data=00 00 29 DC 187 2018-10-27 10:55:45.260 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=6) 188 2018-10-27 10:55:45.260 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=6) 189 2018-10-27 10:55:45.281 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=7) ObjectIndex=0, PropertyId=14, Count=1, StartIndex=1 190 2018-10-27 10:55:45.281 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=7) ObjectIndex=0, PropertyId=14, Count=1, StartIndex=1 191 2018-10-27 10:55:45.287 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=7) 192 2018-10-27 10:55:45.316 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=7) ObjectIndex=0, PropertyId=14, Count=1, StartIndex=1, Data=$04 193 2018-10-27 10:55:45.317 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=7) 194 2018-10-27 10:55:45.317 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=7) 195 2018-10-27 10:55:45.338 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=8) ObjectIndex=0, PropertyId=14, Count=1, StartIndex=1 196 2018-10-27 10:55:45.338 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=8) ObjectIndex=0, PropertyId=14, Count=1, StartIndex=1 197 2018-10-27 10:55:45.343 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=8) 198 2018-10-27 10:55:45.363 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=8) ObjectIndex=0, PropertyId=14, Count=1, StartIndex=1, Data=$04 199 2018-10-27 10:55:45.364 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=8) 200 2018-10-27 10:55:45.364 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=8) 201 2018-10-27 10:55:45.398 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 MemoryWrite (S=9) Count=4, Address=29DC, Data=00 00 00 14 202 2018-10-27 10:55:45.398 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 MemoryWrite (S=9) Count=4, Address=29DC, Data=00 00 00 14 203 2018-10-27 10:55:45.402 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=9) 204 2018-10-27 10:55:45.423 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 MemoryResponse (S=9) Count=4, Address=29DC, Data=00 00 00 14 205 2018-10-27 10:55:45.424 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=9) 206 2018-10-27 10:55:45.424 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=9) 207 2018-10-27 10:55:45.444 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=10) ObjectIndex=3, PropertyId=7, Count=1, StartIndex=1 208 2018-10-27 10:55:45.444 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=10) ObjectIndex=3, PropertyId=7, Count=1, StartIndex=1 209 2018-10-27 10:55:45.448 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=10) 210 2018-10-27 10:55:45.468 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=10) ObjectIndex=3, PropertyId=7, Count=1, StartIndex=1, Data=00 00 2B AC 211 2018-10-27 10:55:45.469 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=10) 212 2018-10-27 10:55:45.469 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=10) 213 2018-10-27 10:55:45.490 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 MemoryWrite (S=11) Count=12, Address=2BAC, Data=00 0A 4B 08 4B 08 4B 08 4B 08 4B 08 214 2018-10-27 10:55:45.490 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 MemoryWrite (S=11) Count=12, Address=2BAC, Data=00 0A 4B 08 4B 08 4B 08 4B 08 4B 08 215 2018-10-27 10:55:45.495 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=11) 216 2018-10-27 10:55:45.521 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 MemoryResponse (S=11) Count=12, Address=2BAC, Data=00 0A 4B 08 4B 08 4B 08 4B 08 4B 08 217 2018-10-27 10:55:45.522 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=11) 218 2018-10-27 10:55:45.522 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=11) 219 2018-10-27 10:55:45.543 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 MemoryWrite (S=12) Count=10, Address=2BB8, Data=4B 07 4B 08 4B 08 13 00 0B 08 220 2018-10-27 10:55:45.543 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 MemoryWrite (S=12) Count=10, Address=2BB8, Data=4B 07 4B 08 4B 08 13 00 0B 08 221 2018-10-27 10:55:45.548 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=12) 222 2018-10-27 10:55:45.568 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 MemoryResponse (S=12) Count=10, Address=2BB8, Data=4B 07 4B 08 4B 08 13 00 0B 08 223 2018-10-27 10:55:45.569 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=12) 224 2018-10-27 10:55:45.569 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=12) 225 2018-10-27 10:55:45.590 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=13) ObjectIndex=2, PropertyId=7, Count=1, StartIndex=1 226 2018-10-27 10:55:45.590 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=13) ObjectIndex=2, PropertyId=7, Count=1, StartIndex=1 227 2018-10-27 10:55:45.594 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=13) 228 2018-10-27 10:55:45.614 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=13) ObjectIndex=2, PropertyId=7, Count=1, StartIndex=1, Data=00 00 26 FC 229 2018-10-27 10:55:45.615 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=13) 230 2018-10-27 10:55:45.615 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=13) 231 2018-10-27 10:55:45.636 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 MemoryWrite (S=14) Count=2, Address=26FC, Data=00 00 232 2018-10-27 10:55:45.636 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 MemoryWrite (S=14) Count=2, Address=26FC, Data=00 00 233 2018-10-27 10:55:45.640 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=14) 235 2018-10-27 10:55:45.660 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 MemoryResponse (S=14) Count=2, Address=26FC, Data=00 00 236 2018-10-27 10:55:45.661 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=14) 237 2018-10-27 10:55:45.690 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=15) ObjectIndex=1, PropertyId=7, Count=1, StartIndex=1 238 2018-10-27 10:55:45.690 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=15) ObjectIndex=1, PropertyId=7, Count=1, StartIndex=1 239 2018-10-27 10:55:45.696 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=15) 240 2018-10-27 10:55:45.716 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=15) ObjectIndex=1, PropertyId=7, Count=1, StartIndex=1, Data=00 00 26 F4 241 2018-10-27 10:55:45.717 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=15) 242 2018-10-27 10:55:45.717 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=15) 243 2018-10-27 10:55:45.738 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 MemoryWrite (S=0) Count=2, Address=26F4, Data=00 00 244 2018-10-27 10:55:45.738 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 MemoryWrite (S=0) Count=2, Address=26F4, Data=00 00 245 2018-10-27 10:55:45.742 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=0) 246 2018-10-27 10:55:45.763 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 MemoryResponse (S=0) Count=2, Address=26F4, Data=00 00 247 2018-10-27 10:55:45.764 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=0) 248 2018-10-27 10:55:45.764 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=0) 249 2018-10-27 10:55:45.785 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=1) ObjectIndex=4, PropertyId=13, Count=1, StartIndex=1, Data=00 FA 00 00 0A 250 2018-10-27 10:55:45.785 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=1) ObjectIndex=4, PropertyId=13, Count=1, StartIndex=1, Data=00 FA 00 00 0A 251 2018-10-27 10:55:45.792 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=1) 252 2018-10-27 10:55:45.811 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=1) ObjectIndex=4, PropertyId=13, Count=1, StartIndex=1, Data=00 FA 00 00 0A 253 2018-10-27 10:55:45.812 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=1) 254 2018-10-27 10:55:45.812 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=1) 255 2018-10-27 10:55:45.833 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=2) ObjectIndex=4, PropertyId=5, Count=1, StartIndex=1, Data=02 00 00 00 00 00 00 00 00 00 256 2018-10-27 10:55:45.833 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=2) ObjectIndex=4, PropertyId=5, Count=1, StartIndex=1, Data=02 00 00 00 00 00 00 00 00 00 257 2018-10-27 10:55:45.839 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=2) 258 2018-10-27 10:55:45.865 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=2) ObjectIndex=4, PropertyId=5, Count=1, StartIndex=1, Data=$01 259 2018-10-27 10:55:45.866 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=2) 260 2018-10-27 10:55:45.866 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=2) 261 2018-10-27 10:55:45.886 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=3) ObjectIndex=3, PropertyId=5, Count=1, StartIndex=1, Data=02 00 00 00 00 00 00 00 00 00 262 2018-10-27 10:55:45.886 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=3) ObjectIndex=3, PropertyId=5, Count=1, StartIndex=1, Data=02 00 00 00 00 00 00 00 00 00 263 2018-10-27 10:55:45.892 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=3) 264 2018-10-27 10:55:45.913 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=3) ObjectIndex=3, PropertyId=5, Count=1, StartIndex=1, Data=$01 265 2018-10-27 10:55:45.914 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=3) 266 2018-10-27 10:55:45.914 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=3) 267 2018-10-27 10:55:45.935 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=4) ObjectIndex=2, PropertyId=5, Count=1, StartIndex=1, Data=02 00 00 00 00 00 00 00 00 00 268 2018-10-27 10:55:45.935 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=4) ObjectIndex=2, PropertyId=5, Count=1, StartIndex=1, Data=02 00 00 00 00 00 00 00 00 00 269 2018-10-27 10:55:45.944 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=4) 270 2018-10-27 10:55:45.961 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=4) ObjectIndex=2, PropertyId=5, Count=1, StartIndex=1, Data=$01 271 2018-10-27 10:55:45.962 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=4) 272 2018-10-27 10:55:45.962 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=4) 273 2018-10-27 10:55:45.983 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=5) ObjectIndex=1, PropertyId=5, Count=1, StartIndex=1, Data=02 00 00 00 00 00 00 00 00 00 274 2018-10-27 10:55:45.983 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueWrite (S=5) ObjectIndex=1, PropertyId=5, Count=1, StartIndex=1, Data=02 00 00 00 00 00 00 00 00 00 275 2018-10-27 10:55:45.988 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=5) 276 2018-10-27 10:55:46.012 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=5) ObjectIndex=1, PropertyId=5, Count=1, StartIndex=1, Data=$01 277 2018-10-27 10:55:46.013 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=5) 278 2018-10-27 10:55:46.014 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=5) 279 2018-10-27 10:55:46.034 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=6) ObjectIndex=6, PropertyId=1, Count=1, StartIndex=1 280 2018-10-27 10:55:46.034 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyValueRead (S=6) ObjectIndex=6, PropertyId=1, Count=1, StartIndex=1 281 2018-10-27 10:55:46.092 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=6) 282 2018-10-27 10:55:46.113 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyValueResponse (S=6) ObjectIndex=6, PropertyId=1, Count=1, StartIndex=1, Data=00 0B 283 2018-10-27 10:55:46.114 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=6) 284 2018-10-27 10:55:46.115 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=6) 285 2018-10-27 10:55:46.135 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyDescriptionRead (S=7) 06 33 00 286 2018-10-27 10:55:46.135 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 PropertyDescriptionRead (S=7) 06 33 00 287 2018-10-27 10:55:46.143 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 T_ACK (S=7) 288 2018-10-27 10:55:46.163 vom Bus System 2.0.1 BME680 BSEC 0.0.1 - 6 PropertyDescriptionResponse (S=7) 06 33 00 00 00 00 00 289 2018-10-27 10:55:46.164 vom Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=7) 290 2018-10-27 10:55:46.164 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_ACK (S=7) 291 2018-10-27 10:55:46.185 zum Bus System 0.0.1 - 2.0.1 BME680 BSEC 6 T_Disconnect
Gruß,
HendrikEinen Kommentar schreiben:
-
Das KNX-LUNOS-CONTROL4 von arcus-eds: https://www.arcus-eds.de/485.htmlEinen Kommentar schreiben:
Einen Kommentar schreiben: