Ankündigung

**Freeman** · 25.12.2020, 14:22

Sooo... ich habs nach fast 1 Jahr mal wieder gewagt mich an das Projekt zu setzen.
Ich bin tatsächlich weitergekommen. Habe ja jetzt den SAMD21G18.

Man nehme als Board in der IDE den Arduino Zero (Native USB Port), dann klappts mit der Kommunikation.
Habe separat Button und Temp getestet, Schaltung läuft.
Dann hab ich die MicroBCU verbunden, RX -> TX (D1) / TX -> RX(D0) und beide KNX Adern. Button auf D3. LED auf D11, Temp/Hum ist n HDC1080 und hängt auf SCL und SDA (D21/D20)

//edit
Habe IDE 1.8.13
und da ich in der IDE die Beta5 nicht gefunden habe, nutze ich 4b
//editend

Ich freu mich riesig, denn ich bekomme ne Ausgabe, aber mit Fehler.
Das Debug-Protokoll gibt ein par deprecated Warnungen aus, aber es wird kompiliert und hochgeladen. Das Log hab ich ganz unten angehängt, falls es von Interesse sein sollte.

Habe schon im Forum nach dem Fehler geschaut. tuxedo meinte möglicherweise ist der Adruino mit ner falschen Frequenz programmiert, hab aber ums verrecken nichts gefunden wie ich das einstelle.

Kann mir jemand weiterhelfen?

Danke euch!

Debug-Ausgabe:

Code:

DEBUG! free ram: 28475 bytes
KONNEKTING DemoSketch
Initialize KonnektingDevice
15/7/255 = 0x7fff
PrgLed 0
PrgState 0
Manufacturer: 0xdead Device: 0xff Revision: 0x00
numberOfCommObjects: 2
memRead: index=0x00 using fctptr data=0xff
_deviceFlags: 11111111
->FACTORY
IA: 0x11fe
Reset triggered!
Reset attempts: 9
Data available: 1
data not useable: 0x01. Expected: 0x03
Reset attempts: 8
Data available: 1
data not useable: 0x01. Expected: 0x03
Reset attempts: 7
Data available: 1
data not useable: 0x01. Expected: 0x03
Reset attempts: 6
Data available: 1
data not useable: 0x01. Expected: 0x03
Reset attempts: 5
Data available: 1
data not useable: 0x01. Expected: 0x03
Reset attempts: 4
Data available: 1
data not useable: 0x01. Expected: 0x03
Reset attempts: 3
Data available: 1
data not useable: 0x01. Expected: 0x03
Reset attempts: 2
Data available: 1
data not useable: 0x01. Expected: 0x03
Reset attempts: 1
Data available: 1
data not useable: 0x01. Expected: 0x03
Reset attempts: 0
Data available: 1
data not useable: 0x01. Expected: 0x03
Reset failed, no answer from TPUART device
Init Error!
KnxDevice startup status: 0x02
Knx init ERROR. Retry after reboot!!
SAMD SystemReset

Code:

C:\Users\User\Documents\arduino-1.8.13\arduino-builder -dump-prefs -logger=machine -hardware C:\Users\User\Documents\arduino-1.8.13\hardware -hardware C:\Users\User\AppData\Local\Arduino15\packages -tools C:\Users\User\Documents\arduino-1.8.13\tools-builder -tools C:\Users\User\Documents\arduino-1.8.13\hardware\tools\avr -tools C:\Users\User\AppData\Local\Arduino15\packages -built-in-libraries C:\Users\User\Documents\arduino-1.8.13\libraries -libraries C:\Users\User\Documents\Arduino\libraries -fqbn=arduino:samd:arduino_zero_native -vid-pid=2341_804D -ide-version=10813 -build-path C:\Users\User\AppData\Local\Temp\arduino_build_359 895 -warnings=default -build-cache C:\Users\User\AppData\Local\Temp\arduino_cache_760 284 -prefs=build.warn_data_percentage=75 -prefs=runtime.tools.CMSIS-Atmel.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\CMSIS-Atmel\1.2.0 -prefs=runtime.tools.CMSIS-Atmel-1.2.0.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\CMSIS-Atmel\1.2.0 -prefs=runtime.tools.arduinoOTA.path=C:\Users\User\ AppData\Local\Arduino15\packages\arduino\tools\ard uinoOTA\1.2.1 -prefs=runtime.tools.arduinoOTA-1.2.1.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\arduinoOTA\1.2.1 -prefs=runtime.tools.arm-none-eabi-gcc.path=C:\Users\User\AppData\Local\Arduino15\pac kages\arduino\tools\arm-none-eabi-gcc\7-2017q4 -prefs=runtime.tools.arm-none-eabi-gcc-7-2017q4.path=C:\Users\User\AppData\Local\Arduino15\ packages\arduino\tools\arm-none-eabi-gcc\7-2017q4 -prefs=runtime.tools.bossac.path=C:\Users\User\AppD ata\Local\Arduino15\packages\arduino\tools\bossac\ 1.7.0-arduino3 -prefs=runtime.tools.bossac-1.7.0-arduino3.path=C:\Users\User\AppData\Local\Arduino1 5\packages\arduino\tools\bossac\1.7.0-arduino3 -prefs=runtime.tools.openocd.path=C:\Users\User\App Data\Local\Arduino15\packages\arduino\tools\openoc d\0.10.0-arduino7 -prefs=runtime.tools.openocd-0.10.0-arduino7.path=C:\Users\User\AppData\Local\Arduino1 5\packages\arduino\tools\openocd\0.10.0-arduino7 -prefs=runtime.tools.CMSIS.path=C:\Users\User\AppDa ta\Local\Arduino15\packages\arduino\tools\CMSIS\4. 5.0 -prefs=runtime.tools.CMSIS-4.5.0.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\CMSIS\4.5.0 -verbose C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino
C:\Users\User\Documents\arduino-1.8.13\arduino-builder -compile -logger=machine -hardware C:\Users\User\Documents\arduino-1.8.13\hardware -hardware C:\Users\User\AppData\Local\Arduino15\packages -tools C:\Users\User\Documents\arduino-1.8.13\tools-builder -tools C:\Users\User\Documents\arduino-1.8.13\hardware\tools\avr -tools C:\Users\User\AppData\Local\Arduino15\packages -built-in-libraries C:\Users\User\Documents\arduino-1.8.13\libraries -libraries C:\Users\User\Documents\Arduino\libraries -fqbn=arduino:samd:arduino_zero_native -vid-pid=2341_804D -ide-version=10813 -build-path C:\Users\User\AppData\Local\Temp\arduino_build_359 895 -warnings=default -build-cache C:\Users\User\AppData\Local\Temp\arduino_cache_760 284 -prefs=build.warn_data_percentage=75 -prefs=runtime.tools.CMSIS-Atmel.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\CMSIS-Atmel\1.2.0 -prefs=runtime.tools.CMSIS-Atmel-1.2.0.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\CMSIS-Atmel\1.2.0 -prefs=runtime.tools.arduinoOTA.path=C:\Users\User\ AppData\Local\Arduino15\packages\arduino\tools\ard uinoOTA\1.2.1 -prefs=runtime.tools.arduinoOTA-1.2.1.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\arduinoOTA\1.2.1 -prefs=runtime.tools.arm-none-eabi-gcc.path=C:\Users\User\AppData\Local\Arduino15\pac kages\arduino\tools\arm-none-eabi-gcc\7-2017q4 -prefs=runtime.tools.arm-none-eabi-gcc-7-2017q4.path=C:\Users\User\AppData\Local\Arduino15\ packages\arduino\tools\arm-none-eabi-gcc\7-2017q4 -prefs=runtime.tools.bossac.path=C:\Users\User\AppD ata\Local\Arduino15\packages\arduino\tools\bossac\ 1.7.0-arduino3 -prefs=runtime.tools.bossac-1.7.0-arduino3.path=C:\Users\User\AppData\Local\Arduino1 5\packages\arduino\tools\bossac\1.7.0-arduino3 -prefs=runtime.tools.openocd.path=C:\Users\User\App Data\Local\Arduino15\packages\arduino\tools\openoc d\0.10.0-arduino7 -prefs=runtime.tools.openocd-0.10.0-arduino7.path=C:\Users\User\AppData\Local\Arduino1 5\packages\arduino\tools\openocd\0.10.0-arduino7 -prefs=runtime.tools.CMSIS.path=C:\Users\User\AppDa ta\Local\Arduino15\packages\arduino\tools\CMSIS\4. 5.0 -prefs=runtime.tools.CMSIS-4.5.0.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\CMSIS\4.5.0 -verbose C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino
Using board 'arduino_zero_native' from platform in folder: C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11
Using core 'arduino' from platform in folder: C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11
Detecting libraries used...
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-g++" -mcpu=cortex-m0plus -mthumb -c -g -Os -w -std=gnu++11 -ffunction-sections -fdata-sections -fno-threadsafe-statics -nostdlib --param max-inline-insns-single=500 -fno-rtti -fno-exceptions -w -x c++ -E -CC -DF_CPU=48000000L -DARDUINO=10813 -DARDUINO_SAMD_ZERO -DARDUINO_ARCH_SAMD -D__SAMD21G18A__ -DUSB_VID=0x2341 -DUSB_PID=0x804d -DUSBCON "-DUSB_MANUFACTURER=\"Arduino LLC\"" "-DUSB_PRODUCT=\"Arduino Zero\"" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS\\4.5.0/CMSIS/Include/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS-Atmel\\1.2.0/CMSIS/Device/ATMEL/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated-avr-comp" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\variants\\ar duino_zero" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\sketch\\knx_btn_temp_led.ino.cpp" -o nul -DARDUINO_LIB_DISCOVERY_PHASE
Alternatives for KonnektingDevice.h: [KONNEKTING_Device_Library@1.0.0-BETA4b]
ResolveLibrary(KonnektingDevice.h)
-> cUserdates: [KONNEKTING_Device_Library@1.0.0-BETA4b]
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-g++" -mcpu=cortex-m0plus -mthumb -c -g -Os -w -std=gnu++11 -ffunction-sections -fdata-sections -fno-threadsafe-statics -nostdlib --param max-inline-insns-single=500 -fno-rtti -fno-exceptions -w -x c++ -E -CC -DF_CPU=48000000L -DARDUINO=10813 -DARDUINO_SAMD_ZERO -DARDUINO_ARCH_SAMD -D__SAMD21G18A__ -DUSB_VID=0x2341 -DUSB_PID=0x804d -DUSBCON "-DUSB_MANUFACTURER=\"Arduino LLC\"" "-DUSB_PRODUCT=\"Arduino Zero\"" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS\\4.5.0/CMSIS/Include/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS-Atmel\\1.2.0/CMSIS/Device/ATMEL/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated-avr-comp" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\variants\\ar duino_zero" "-IC:\\Users\\User\\Documents\\Arduino\\libraries\\K ONNEKTING_Device_Library\\src" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\sketch\\knx_btn_temp_led.ino.cpp" -o nul -DARDUINO_LIB_DISCOVERY_PHASE
Alternatives for Wire.h: [Wire@1.0]
ResolveLibrary(Wire.h)
-> cUserdates: [Wire@1.0]
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-g++" -mcpu=cortex-m0plus -mthumb -c -g -Os -w -std=gnu++11 -ffunction-sections -fdata-sections -fno-threadsafe-statics -nostdlib --param max-inline-insns-single=500 -fno-rtti -fno-exceptions -w -x c++ -E -CC -DF_CPU=48000000L -DARDUINO=10813 -DARDUINO_SAMD_ZERO -DARDUINO_ARCH_SAMD -D__SAMD21G18A__ -DUSB_VID=0x2341 -DUSB_PID=0x804d -DUSBCON "-DUSB_MANUFACTURER=\"Arduino LLC\"" "-DUSB_PRODUCT=\"Arduino Zero\"" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS\\4.5.0/CMSIS/Include/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS-Atmel\\1.2.0/CMSIS/Device/ATMEL/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated-avr-comp" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\variants\\ar duino_zero" "-IC:\\Users\\User\\Documents\\Arduino\\libraries\\K ONNEKTING_Device_Library\\src" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\libraries\\W ire" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\sketch\\knx_btn_temp_led.ino.cpp" -o nul -DARDUINO_LIB_DISCOVERY_PHASE
Using cached library dependencies for file: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src\DebugUtil.cpp
Using cached library dependencies for file: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src\KnxComObject.cpp
Using cached library dependencies for file: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src\KnxDevice.cpp
Using cached library dependencies for file: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src\KnxTelegram.cpp
Using cached library dependencies for file: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src\KnxTpUart.cpp
Using cached library dependencies for file: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src\KonnektingDevice.cpp
Using cached library dependencies for file: C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\libraries\Wire\Wire.cpp
Generating function prototypes...
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-g++" -mcpu=cortex-m0plus -mthumb -c -g -Os -w -std=gnu++11 -ffunction-sections -fdata-sections -fno-threadsafe-statics -nostdlib --param max-inline-insns-single=500 -fno-rtti -fno-exceptions -w -x c++ -E -CC -DF_CPU=48000000L -DARDUINO=10813 -DARDUINO_SAMD_ZERO -DARDUINO_ARCH_SAMD -D__SAMD21G18A__ -DUSB_VID=0x2341 -DUSB_PID=0x804d -DUSBCON "-DUSB_MANUFACTURER=\"Arduino LLC\"" "-DUSB_PRODUCT=\"Arduino Zero\"" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS\\4.5.0/CMSIS/Include/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS-Atmel\\1.2.0/CMSIS/Device/ATMEL/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated-avr-comp" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\variants\\ar duino_zero" "-IC:\\Users\\User\\Documents\\Arduino\\libraries\\K ONNEKTING_Device_Library\\src" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\libraries\\W ire" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\sketch\\knx_btn_temp_led.ino.cpp" -o "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\preproc\\ctags_target_for_gcc_minus_e. cpp" -DARDUINO_LIB_DISCOVERY_PHASE
"C:\\Users\\User\\Documents\\arduino-1.8.13\\tools-builder\\ctags\\5.8-arduino11/ctags" -u --language-force=c++ -f - --c++-kinds=svpf --fields=KSTtzns --line-directives "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\preproc\\ctags_target_for_gcc_minus_e. cpp"
Sketch wird kompiliert...
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-g++" -mcpu=cortex-m0plus -mthumb -c -g -Os -std=gnu++11 -ffunction-sections -fdata-sections -fno-threadsafe-statics -nostdlib --param max-inline-insns-single=500 -fno-rtti -fno-exceptions -MMD -DF_CPU=48000000L -DARDUINO=10813 -DARDUINO_SAMD_ZERO -DARDUINO_ARCH_SAMD -D__SAMD21G18A__ -DUSB_VID=0x2341 -DUSB_PID=0x804d -DUSBCON "-DUSB_MANUFACTURER=\"Arduino LLC\"" "-DUSB_PRODUCT=\"Arduino Zero\"" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS\\4.5.0/CMSIS/Include/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS-Atmel\\1.2.0/CMSIS/Device/ATMEL/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated-avr-comp" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\variants\\ar duino_zero" "-IC:\\Users\\User\\Documents\\Arduino\\libraries\\K ONNEKTING_Device_Library\\src" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\libraries\\W ire" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\sketch\\knx_btn_temp_led.ino.cpp" -o "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\sketch\\knx_btn_temp_led.ino.cpp.o"
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:79:32: warning: 'B00000000' is deprecated: use 0b00000000 instead [-Wdeprecated-declarations]
KNX_PRIORITY_SYSTEM_VALUE = B00000000,
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:45:3: note: declared here
B00000000 DEPRECATED(0b00000000) = 0,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:80:32: warning: 'B00000100' is deprecated: use 0b00000100 instead [-Wdeprecated-declarations]
KNX_PRIORITY_HIGH_VALUE = B00000100,
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:73:3: note: declared here
B00000100 DEPRECATED(0b00000100) = 4,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:81:32: warning: 'B00001000' is deprecated: use 0b00001000 instead [-Wdeprecated-declarations]
KNX_PRIORITY_ALARM_VALUE = B00001000,
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:96:3: note: declared here
B00001000 DEPRECATED(0b00001000) = 8,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:82:32: warning: 'B00001100' is deprecated: use 0b00001100 instead [-Wdeprecated-declarations]
KNX_PRIORITY_NORMAL_VALUE = B00001100
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:116:3: note: declared here
B00001100 DEPRECATED(0b00001100) = 12,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:86:32: warning: 'B00000000' is deprecated: use 0b00000000 instead [-Wdeprecated-declarations]
KNX_COMMAND_VALUE_READ = B00000000,
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:45:3: note: declared here
B00000000 DEPRECATED(0b00000000) = 0,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:87:32: warning: 'B00000001' is deprecated: use 0b00000001 instead [-Wdeprecated-declarations]
KNX_COMMAND_VALUE_RESPONSE = B00000001,
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:53:3: note: declared here
B00000001 DEPRECATED(0b00000001) = 1,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:88:32: warning: 'B00000010' is deprecated: use 0b00000010 instead [-Wdeprecated-declarations]
KNX_COMMAND_VALUE_WRITE = B00000010,
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:60:3: note: declared here
B00000010 DEPRECATED(0b00000010) = 2,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:89:32: warning: 'B00001010' is deprecated: use 0b00001010 instead [-Wdeprecated-declarations]
KNX_COMMAND_MEMORY_WRITE = B00001010
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:106:3: note: declared here
B00001010 DEPRECATED(0b00001010) = 10,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'void KnxTelegram::ChangePriority(e_KnxPriority)':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:98:45: warning: 'B00001100' is deprecated: use 0b00001100 instead [-Wdeprecated-declarations]
#define CONTROL_FIELD_PRIORITY_MASK B00001100
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:220:21: note: in expansion of macro 'CONTROL_FIELD_PRIORITY_MASK'
{ _controlField &= ~CONTROL_FIELD_PRIORITY_MASK; _controlField |= priority & CONTROL_FIELD_PRIORITY_MASK;}
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:116:3: note: declared here
B00001100 DEPRECATED(0b00001100) = 12,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:98:45: warning: 'B00001100' is deprecated: use 0b00001100 instead [-Wdeprecated-declarations]
#define CONTROL_FIELD_PRIORITY_MASK B00001100
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:220:78: note: in expansion of macro 'CONTROL_FIELD_PRIORITY_MASK'
{ _controlField &= ~CONTROL_FIELD_PRIORITY_MASK; _controlField |= priority & CONTROL_FIELD_PRIORITY_MASK;}
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:116:3: note: declared here
B00001100 DEPRECATED(0b00001100) = 12,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'e_KnxPriority KnxTelegram::GetPriority() const':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:98:45: warning: 'B00001100' is deprecated: use 0b00001100 instead [-Wdeprecated-declarations]
#define CONTROL_FIELD_PRIORITY_MASK B00001100
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:223:41: note: in expansion of macro 'CONTROL_FIELD_PRIORITY_MASK'
{return (e_KnxPriority)(_controlField & CONTROL_FIELD_PRIORITY_MASK);}
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:116:3: note: declared here
B00001100 DEPRECATED(0b00001100) = 12,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'void KnxTelegram::SetRepeated()':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:97:49: warning: 'B11011111' is deprecated: use 0b11011111 instead [-Wdeprecated-declarations]
#define CONTROL_FIELD_SET_REPEATED(x) (x&=B11011111)
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:226:3: note: in expansion of macro 'CONTROL_FIELD_SET_REPEATED'
{ CONTROL_FIELD_SET_REPEATED(_controlField);};
^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:515:3: note: declared here
B11011111 DEPRECATED(0b11011111) = 223,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'boolean KnxTelegram::IsRepeated() const':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:96:45: warning: 'B00100000' is deprecated: use 0b00100000 instead [-Wdeprecated-declarations]
#define CONTROL_FIELD_REPEATED_MASK B00100000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:229:22: note: in expansion of macro 'CONTROL_FIELD_REPEATED_MASK'
{if (_controlField & CONTROL_FIELD_REPEATED_MASK ) return false; else return true ; }
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:198:3: note: declared here
B00100000 DEPRECATED(0b00100000) = 32,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'boolean KnxTelegram::IsMulticast() const':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:104:48: warning: 'B10000000' is deprecated: use 0b10000000 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK B10000000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:252:21: note: in expansion of macro 'ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK'
{return (_routing & ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK);}
^
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:420:3: note: declared here
B10000000 DEPRECATED(0b10000000) = 128,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'void KnxTelegram::SetMulticast(boolean)':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:104:48: warning: 'B10000000' is deprecated: use 0b10000000 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK B10000000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:255:24: note: in expansion of macro 'ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK'
{ if (mode) _routing|= ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK;
^
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:420:3: note: declared here
B10000000 DEPRECATED(0b10000000) = 128,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:104:48: warning: 'B10000000' is deprecated: use 0b10000000 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK B10000000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:256:21: note: in expansion of macro 'ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK'
else _routing &= ~ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK; }
^
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:420:3: note: declared here
B10000000 DEPRECATED(0b10000000) = 128,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'void KnxTelegram::ChangeRoutingCounter(byte)':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:105:48: warning: 'B01110000' is deprecated: use 0b01110000 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_COUNTER_MASK B01110000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:259:31: note: in expansion of macro 'ROUTING_FIELD_COUNTER_MASK'
{ counter <<= 4; _routing &= ~ROUTING_FIELD_COUNTER_MASK; _routing |= (counter & ROUTING_FIELD_COUNTER_MASK); }
^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:389:3: note: declared here
B01110000 DEPRECATED(0b01110000) = 112,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:105:48: warning: 'B01110000' is deprecated: use 0b01110000 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_COUNTER_MASK B01110000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:259:82: note: in expansion of macro 'ROUTING_FIELD_COUNTER_MASK'
{ counter <<= 4; _routing &= ~ROUTING_FIELD_COUNTER_MASK; _routing |= (counter & ROUTING_FIELD_COUNTER_MASK); }
^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:389:3: note: declared here
B01110000 DEPRECATED(0b01110000) = 112,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'byte KnxTelegram::GetRoutingCounter() const':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:105:48: warning: 'B01110000' is deprecated: use 0b01110000 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_COUNTER_MASK B01110000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:262:23: note: in expansion of macro 'ROUTING_FIELD_COUNTER_MASK'
{ return ((_routing & ROUTING_FIELD_COUNTER_MASK)>>4); }
^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:389:3: note: declared here
B01110000 DEPRECATED(0b01110000) = 112,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'void KnxTelegram::SetPayloadLength(byte)':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:106:48: warning: 'B00001111' is deprecated: use 0b00001111 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_PAYLOAD_LENGTH_MASK B00001111
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:265:15: note: in expansion of macro 'ROUTING_FIELD_PAYLOAD_LENGTH_MASK'
{ _routing&= ~ROUTING_FIELD_PAYLOAD_LENGTH_MASK ; _routing |= length & ROUTING_FIELD_PAYLOAD_LENGTH_MASK; }
^
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:131:3: note: declared here
B00001111 DEPRECATED(0b00001111) = 15,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:106:48: warning: 'B00001111' is deprecated: use 0b00001111 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_PAYLOAD_LENGTH_MASK B00001111
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:265:72: note: in expansion of macro 'ROUTING_FIELD_PAYLOAD_LENGTH_MASK'
{ _routing&= ~ROUTING_FIELD_PAYLOAD_LENGTH_MASK ; _routing |= length & ROUTING_FIELD_PAYLOAD_LENGTH_MASK; }
^
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:131:3: note: declared here
B00001111 DEPRECATED(0b00001111) = 15,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'byte KnxTelegram::GetPayloadLength() const':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:106:48: warning: 'B00001111' is deprecated: use 0b00001111 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_PAYLOAD_LENGTH_MASK B00001111
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:268:21: note: in expansion of macro 'ROUTING_FIELD_PAYLOAD_LENGTH_MASK'
{return (_routing & ROUTING_FIELD_PAYLOAD_LENGTH_MASK);}
^
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_359 895\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:131:3: note: declared here
B00001111 DEPRECATED(0b00001111) = 15,
^~~~~~~~~
Compiling libraries...
Compiling library "KONNEKTING_Device_Library"
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_359 895\libraries\KONNEKTING_Device_Library\KnxTelegra m.cpp.o
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_359 895\libraries\KONNEKTING_Device_Library\DebugUtil. cpp.o
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_359 895\libraries\KONNEKTING_Device_Library\KnxDevice. cpp.o
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_359 895\libraries\KONNEKTING_Device_Library\KnxComObje ct.cpp.o
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_359 895\libraries\KONNEKTING_Device_Library\KnxTpUart. cpp.o
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_359 895\libraries\KONNEKTING_Device_Library\Konnekting Device.cpp.o
Compiling library "Wire"
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_359 895\libraries\Wire\Wire.cpp.o
Compiling core...
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_359 895\core\variant.cpp.o
Using precompiled core: C:\Users\User\AppData\Local\Temp\arduino_cache_760 284\core\core_arduino_samd_arduino_zero_native_91e 273adf6e8ac7a10158c7ef2e10266.a
Linking everything together...
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-g++" "-LC:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895" -Os -Wl,--gc-sections -save-temps "-TC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\variants\\ar duino_zero/linker_scripts/gcc/flash_with_bootloader.ld" "-Wl,-Map,C:\\Users\\User\\AppData\\Local\\Temp\\arduino _build_359895/knx_btn_temp_led.ino.map" --specs=nano.specs --specs=nosys.specs -mcpu=cortex-m0plus -mthumb -Wl,--cref -Wl,--check-sections -Wl,--gc-sections -Wl,--unresolved-symbols=report-all -Wl,--warn-common -Wl,--warn-section-align -o "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895/knx_btn_temp_led.ino.elf" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\sketch\\knx_btn_temp_led.ino.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\libraries\\KONNEKTING_Device_Library\\ DebugUtil.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\libraries\\KONNEKTING_Device_Library\\ KnxComObject.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\libraries\\KONNEKTING_Device_Library\\ KnxDevice.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\libraries\\KONNEKTING_Device_Library\\ KnxTelegram.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\libraries\\KONNEKTING_Device_Library\\ KnxTpUart.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\libraries\\KONNEKTING_Device_Library\\ KonnektingDevice.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\libraries\\Wire\\Wire.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895\\core\\variant.cpp.o" -Wl,--start-group "-LC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS\\4.5.0/CMSIS/Lib/GCC/" -larm_cortexM0l_math -lm "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895/..\\arduino_cache_760284\\core\\core_arduino_samd_ arduino_zero_native_91e273adf6e8ac7a10158c7ef2e102 66.a" -Wl,--end-group
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-objcopy" -O binary "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895/knx_btn_temp_led.ino.elf" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895/knx_btn_temp_led.ino.bin"
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-objcopy" -O ihex -R .eeprom "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895/knx_btn_temp_led.ino.elf" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895/knx_btn_temp_led.ino.hex"
Bibliothek KONNEKTING_Device_Library in Version 1.0.0-BETA4b im Ordner: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library wird verwendet
Bibliothek Wire in Version 1.0 im Ordner: C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\libraries\Wire wird verwendet
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-size" -A "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_359895/knx_btn_temp_led.ino.elf"
Der Sketch verwendet 41284 Bytes (15%) des Programmspeicherplatzes. Das Maximum sind 262144 Bytes.
Globale Variablen verwenden 3620 Bytes (11%) des dynamischen Speichers, 29148 Bytes für lokale Variablen verbleiben. Das Maximum sind 32768 Bytes.
Erzwinge Reset durch öffnen/schließen mit 1200 bps auf dem Port COM9
PORTS {COM3, COM4, COM9, } / {COM3, COM4, COM9, } => {}
PORTS {COM3, COM4, COM9, } / {COM3, COM4, COM6, COM9, } => {COM6, }
Found upload port: COM6
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\tools\bossac\1.7.0-arduino3/bossac.exe -i -d --port=COM6 -U true -i -e -w -v C:\Users\User\AppData\Local\Temp\arduino_build_359 895/knx_btn_temp_led.ino.bin -R
Set binary mode
readWord(addr=0)=0x20007ffc
readWord(addr=0xe000ed00)=0x410cc601
readWord(addr=0x41002018)=0x10010305
version()=v2.0 [Arduino:XYZ] Dec 20 2016 15:36:41
chipId=0x10010005
Connected at 921600 baud
readWord(addr=0)=0x20007ffc
readWord(addr=0xe000ed00)=0x410cc601
readWord(addr=0x41002018)=0x10010305
Atmel SMART device 0x10010005 found
write(addr=0x20004000,size=0x34)
writeWord(addr=0x20004030,value=0x10)
writeWord(addr=0x20004020,value=0x20008000)
Device : ATSAMD21G18A
readWord(addr=0)=0x20007ffc
readWord(addr=0xe000ed00)=0x410cc601
readWord(addr=0x41002018)=0x10010305
Chip ID : 10010005
version()=v2.0 [Arduino:XYZ] Dec 20 2016 15:36:41
Version : v2.0 [Arduino:XYZ] Dec 20 2016 15:36:41
Address : 8192
Pages : 3968
Page Size : 64 bytes
Total Size : 248KB
Planes : 1
Lock Regions : 16
Locked : readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
readWord(addr=0x41004020)=0xffff
none
readWord(addr=0x41004018)=0
Security : false
Boot Flash : true
readWord(addr=0x40000834)=0x7000a
BOD : true
readWord(addr=0x40000834)=0x7000a
BOR : true
Arduino : FAST_CHIP_ERASE
Arduino : FAST_MULTI_PAGE_WRITE
Arduino : CAN_CHECKSUM_MEMORY_BUFFER
Erase flash
chipErase(addr=0x2000)
done in 0.955 seconds

Write 41284 bytes to flash (646 pages)
write(addr=0x20005000,size=0x1000)
writeBuffer(scr_addr=0x20005000, dst_addr=0x2000, size=0x1000)
[== ] 9% (64/646 pages)write(addr=0x20005000,size=0x1000)
writeBuffer(scr_addr=0x20005000, dst_addr=0x3000, size=0x1000)
[===== ] 19% (128/646 pages)write(addr=0x20005000,size=0x1000)
writeBuffer(scr_addr=0x20005000, dst_addr=0x4000, size=0x1000)
[======== ] 29% (192/646 pages)write(addr=0x20005000,size=0x1000)
writeBuffer(scr_addr=0x20005000, dst_addr=0x5000, size=0x1000)
[=========== ] 39% (256/646 pages)write(addr=0x20005000,size=0x1000)
writeBuffer(scr_addr=0x20005000, dst_addr=0x6000, size=0x1000)
[============== ] 49% (320/646 pages)write(addr=0x20005000,size=0x1000)
writeBuffer(scr_addr=0x20005000, dst_addr=0x7000, size=0x1000)
[================= ] 59% (384/646 pages)write(addr=0x20005000,size=0x1000)
writeBuffer(scr_addr=0x20005000, dst_addr=0x8000, size=0x1000)
[==================== ] 69% (448/646 pages)write(addr=0x20005000,size=0x1000)
writeBuffer(scr_addr=0x20005000, dst_addr=0x9000, size=0x1000)
[======================= ] 79% (512/646 pages)write(addr=0x20005000,size=0x1000)
writeBuffer(scr_addr=0x20005000, dst_addr=0xa000, size=0x1000)
[========================== ] 89% (576/646 pages)write(addr=0x20005000,size=0x1000)
writeBuffer(scr_addr=0x20005000, dst_addr=0xb000, size=0x1000)
[============================= ] 99% (640/646 pages)write(addr=0x20005000,size=0x180)
writeBuffer(scr_addr=0x20005000, dst_addr=0xc000, size=0x180)
[==============================] 100% (646/646 pages)
done in 0.247 seconds

Verify 41284 bytes of flash with checksum.
checksumBuffer(start_addr=0x2000, size=0x1000) = 2063
checksumBuffer(start_addr=0x3000, size=0x1000) = 984f
checksumBuffer(start_addr=0x4000, size=0x1000) = 4c32
checksumBuffer(start_addr=0x5000, size=0x1000) = 15cf
checksumBuffer(start_addr=0x6000, size=0x1000) = 48d3
checksumBuffer(start_addr=0x7000, size=0x1000) = 8fad
checksumBuffer(start_addr=0x8000, size=0x1000) = 7eef
checksumBuffer(start_addr=0x9000, size=0x1000) = dfa3
checksumBuffer(start_addr=0xa000, size=0x1000) = 2fd8
checksumBuffer(start_addr=0xb000, size=0x1000) = f12c
checksumBuffer(start_addr=0xc000, size=0x144) = c92f
Verify successful
done in 0.037 seconds
CPU reset.
readWord(addr=0)=0x20007ffc
readWord(addr=0xe000ed00)=0x410cc601
readWord(addr=0x41002018)=0x10010305
writeWord(addr=0xe000ed0c,value=0x5fa0004)

**Albatros62** · 25.12.2020, 21:15

Die Parameter des Boards wie z.B. die Taktfrequenz stehen in der board.txt (gibt es an verschiedenen Stellen, neben dem Arduino-Programmverzeichnis auch im App-Verzeichnis. Versuch mal C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\.....). Bei mir steht dort eine Taktfrequenz von 48MHz (arduino_zero_native.build.f_cpu=48000000L). Die Taktfrequenz ist letztlich vom Board abhängig. Sollte dein Board nicht vorhanden sein und der Hersteller auch keine board.txt anbieten, so versuch es vielleicht damit, eine Kopie des vorhandene Eintrags passend abzuändern. Eigentlich sollte es auch gehen, indem man die Taktfrequenz (als #define F_CPU=) im Programmtext eingibt. Welche Taktfrequenz das Board hat kann man über ein kleines Testprogramm (delay(500); LED=1;delay(500);LED)=0

herausfinden. Blinkt die LED im 1s-Rhythmus, dann stimmt die Frequenz. Ansonsten muss man schätzen und ausprobieren.

**Freeman** · 25.12.2020, 21:29

Vielen Dank, habs soweit auch mal getestet. Bei 48Mhz ist die LED minimal schneller, habs dann auf 8Mhz resp. 16Mhz gestellt, da wars recht gleich zum Sekundentakt. Im Demosketch hat das aber keinen Unterschied gemacht. Leider nach wie vor

Hast du / jemand noch ne Idee?

Code:

data not useable: 0x01. Expected: 0x03

**Albatros62** · 25.12.2020, 21:43

Zwischen 8MHz, 16MHz und 48MHz sollte eigentlich ein gewaltiger Unterschied sein. Sehr seltsam.

**Freeman** · 25.12.2020, 21:59

Vielleicht liegts auch nicht am Takt der CPU.
Ich weiss nur bei meinem CAN Bus Projekt gabs ne Funktion mit der ich die Einstellung vom Quarz für den seriellen Bus gemacht hab.
Aber die war halt MCP2515 spezifisch und auch entsprechend in der lib vorhanden.

vielleicht liegts auch nicht an der Frequenz, aber im anderen Thread klang das sehr logisch und war das identische Fehlerbild.
Vielleicht muss ich ja tuxedo mal verlinken

tuxedo

**Albatros62** · 25.12.2020, 23:01

Beim CAN-Bus gibt es unterschiedliche Geschwindigkeiten auf dem Bus. Bei KNX sind das immer 9600 Baud. Der MCP2515 ist per SPI mit dem Prozessor verbunden. Daher ist die Prozessorgeschwindigkeit für die Kommunikation mit dem MCP zweitrangig. Die BCU ist per UART mit dem Prozessor verbunden (mit 19200 Baud). Daher muss die lib die UART-Geschwindigkeit des Prozessors korrekt einstellen. Die Einstellungen der entsprechenden Register berechnen sich aus dem Prozessortakt. Die Information darüber erhält die lib über die Direktive F_CPU (genau wie die delay-Funktion). Das muss hier also alles passen. Bei Arduino steht die Direktive in der board.txt. Hat man z.B. einen Pro Mini, dann gibt es mehrere Varianten mit unterschiedlichen Betriebsspannungen und dadurch unterschiedlichen Taktraten (die 3,3V-Variante kann keine 16MHz und hat deshalb einen 8MHz-Taktgeber). Eigentlich sollte der Takt bei Auswahl des richtigen Boards klappen. Leider kenne ich den Zero nicht und deshalb auch nicht die typischen Fehler. Vielleicht liegt es ja an etwas ganz anderem.

**Freeman** · 26.12.2020, 08:17

Ich kann dir selbst nicht genau sagen was hier richtig ist und was nicht.
Ich hab son China Ding. Drauf steht SAMD21 Mini
Hab schon ein paar andere aus den Board-Configs ausgewählt, aber da klappt nicht mal der Upload.

Ich habs jetzt erst mal nur über die F_CPU Einstellung per Sketch probiert, dann mach ichs noch mal per board.txt.
Aber er scheint wirklich die 48Mhz zu machen.

//edit
Produktbeschreibung ebay:
USB SAMD21 M0 Mini WeMos D1 ARM Cortex M0 32-Bit extension For Arduino Zero UNO

Detailseite ist nach 1 Jahr nat. nicht mehr verfügbar

**Albatros62** · 26.12.2020, 09:37

Der SAMD21 M0 Mini WeMos arbeitet mit 48MHz. Das wäre i.O. Allerdings habe ich vor ziemlich genau einem Jahr darauf hingewiesen, dass die MicroBCU keine 5V verträgt. An deiner Stelle würde ich 20€ in eine neue investieren. Die Debug-Ausgabe zeigt, dass die Initialisierung der BCU fehlschlägt. Das kann auch ein zerschossener Eingang der MicroBCU sein.

**Eugenius** · 26.12.2020, 11:24

Es sieht so aus, als ob RX/TX Pins nicht richtig verbunden sind.
Man sieht f
Dass etwas rein kommt, aber nichts zu MicroBCU gesendet wird.
Also, TX SAMD <> RX BCU checken.
evtl. damit probieren:
https://github.com/Adminius/KNX_sniffer

**Freeman** · 26.12.2020, 12:30

//edit6
Post irrelevant, Fehler gefunden (Lösung siehe unten)
//endedit6

Danke Eugenius

Also ich habs noch mal gecheckt und auch mit nem anderen Kabel, aber der Fehler bleibt.
Ich hab sogar im kurz bei 2-3 Retries die Verbindung gekappt von TX(SAMD) zu RX (BCU). Da kam dann keine Rückmeldung mehr für die Versuche, nachdem ichs wieder Verbunden hatte ging es. Also er bekommt Rückmeldungen.
Ich guck mal, dass ich den Link jetzt mal teste.

//edit

KNX initialisation................... failed

//edit2

Da wir ja oben immer auf 0x01 eine 0x03 bekommen hab ich mal DEBUGSERIAL.print(KNX_SERIAL.available()); eingefügt.
Es kommt eine 0...

//edit3

hab jetzt DEBUGSERIAL.print(KNX_SERIAL.read()); eingefügt, jetzt kommt "-1"

//edit4
für alle Fälle noch mal ein Bild der Schaltung, vielleicht ist da auch was schief.

IMG_8849.JPEG

//edit 5
wenn ich TX SAMD auf RX SAMD schleife, dann kommt das gleiche Ergebnis

//edit 6
sooo ... mal die Spannung am Bus getestet... kam zwar am Messpunkt an, aber durch meine doch recht abenteuerliche Konstruktion kams eben nicht am Chip an... da lagen nur 0.2V an... jetzt korrigiert und taddaaa....

Code:

Init successful
KnxDevice startup status: 0x00
Toggle LED every 2500 ms.
Setup is ready. go to loop...
Reset triggered!
HOT RESET case
Reset attempts: 9
Data available: 1
data not useable: 0xde. Expected: 0x03
Data available: 1
Reset successful
Init : Normal mode started

**Freeman** · 26.12.2020, 17:51

Direkt mal noch ein paar spannende Fragen.

Stand:
Ich hab ne kdevice.xml erstellt anhand eines Vorbilds und die Suite läuft auch. Jetzt muss ich mich mal an das Sketch machen.
In der Zwischenzeit hatte ich probiert den SAMD21 per KNX mit Strom zu versorgen aber irgendwie klappt da was nicht.

1. Sowohl auf 3V3 als auch auf 5V geht zwar die Power LED an, aber nichts weiter passiert.
Ich kann auch dann die Prog LED nicht anschalten. Bin mir jetzt auch nicht sicher, ob ich alles richtig gemacht hab. Habe GND vom KNX Bus mit dem GND vom SAMD verbunden und den 3V3 mit VIN bzw auch mit 5V getestet, als ich dann gelesen hatte, das der 5V VIN braucht.

2. Wenn ich das/den wie auch immer Sketch per USB lade, dann klappt alles soweit, wenn ich dann aber resette passiert nichts mehr. Genauso, wenn ich Stromzufuhr trenne und wieder verbinde. Unterschied zu Punkt 1.: Die TX LED (glaube die integrierte Status LED ist das) geht an und leuchtet.

**Eugenius** · 26.12.2020, 17:55

Lass 5V bitte unbenutzt und bleib nur beim 3.3V

Ich nehme an, du lädst Sketch mit eingeschaltetem Debug hoch, der wiederum erwartet, dass USB angesteckt ist. Erist.Debug abschalten, USB trennen

**Freeman** · 26.12.2020, 19:07

Top danke... das wars...
Aber GND vom KNX Bus nehmen war schon richtig? Klar woher auch sonst... hab ja sonst keinen

jetzt kommt das nächste Problem. (inzwischen noch zig andere gelöst)

Kompilieren schlägt fehl und die Fehlermeldung sagt mir jetzt nichts. Da der Demo Sketch läuft, wirds irgendwas sein, was ich geschrieben hab bzw. von anderen Sketches kopiert hab.

Fehlermeldung wegen der länge ganz unten... wir brauchen hier im Forum mal nen Einklappmechanismus für so lange Dinger ^^

Mein Code:

Code:

#include <KonnektingDevice.h>
#include <ClosedCube_HDC1080.h>

// include device related configuration code, created by "KONNEKTING CodeGenerator"
#include "kdevice_temphumsensor.h"

// ################################################
// ### BOARD CONFIGURATION
// ################################################



#ifdef ARDUINO_ARCH_SAMD
// Zero/M0
#define KNX_SERIAL Serial1 // D0=RX/D1=TX
#define PROG_LED_PIN 11 // External LED
#define TEST_LED LED_BUILTIN // On board LED on pin D13
#define PROG_BUTTON_PIN 3 // pin with interrupt
#define DEBUGSERIAL SerialUSB // USB port
// Arduino Zero has no "real" internal EEPROM,
// so we can use an external I2C EEPROM.
#include "EEPROM_24AA256.h" // external EEPROM
ClosedCube_HDC1080 hdc1080;

#else
// All other boards
#error "Sorry, you board is not supported"
#endif

// ################################################
// ### DEBUG CONFIGURATION
// ################################################
#define KDEBUG // comment this line to disable DEBUG mode
#ifdef KDEBUG
#include <DebugUtil.h>
#endif

// ################################################
// ### Global variables, sketch related
// ################################################
uint8_t param_cyclic_send_rate;

// ################################################
// ### set ProgLED status
// ################################################
//this function is used to indicate programming mode.
//you can use LED, LCD display or what ever you want...
void progLed(bool state)
{
digitalWrite(PROG_LED_PIN, state);
}


// ################################################
// ### SETUP
// ################################################

void setup()
{

// debug related stuff
#ifdef KDEBUG
// Start debug serial with 9600 bauds
DEBUGSERIAL.begin(115200);
while (!DEBUGSERIAL)

// make debug serial port known to debug class
// Means: KONNEKTING will use the same serial port for console debugging
Debug.setPrintStream(&DEBUGSERIAL);
#endif



Konnekting.setMemoryReadFunc(&readMemory);
Konnekting.setMemoryWriteFunc(&writeMemory);
Konnekting.setMemoryUpdateFunc(&updateMemory);
Konnekting.setMemoryCommitFunc(&commitMemory);


// Initialize KNX enabled Arduino Board
Konnekting.init(KNX_SERIAL,
&progLed,
MANUFACTURER_ID,
DEVICE_ID,
REVISION);

pinMode(PROG_BUTTON_PIN, INPUT_PULLUP);
if(!digitalRead(PROG_BUTTON_PIN))
{
Debug.println(F("Jumper set to ProgMode. Starting programming mode..."));
Konnekting.setProgState(true);
}

if (!Konnekting.isFactorySetting())
{
param_cyclic_send_rate = (uint8_t)Konnekting.getUINT8Param(PARAM_cyclic_sen d_rate_temperature);
}
else
{
Debug.println(F("Device is in factory mode. Starting programming mode..."));
Konnekting.setProgState(true);
}
hdc1080.begin(0x40);
Debug.println(F("Setup is ready. go to loop..."));
Debug.print("Manufacturer ID=0x");
Debug.print("Device ID=0x");

}





// ################################################
// ### LOOP
// ################################################

void loop()
{

// Do KNX related stuff (like sending/receiving KNX telegrams)
// This is required in every KONNEKTING aplication sketch
Knx.task();


/*
* only do measurements and other sketch related stuff if not in programming mode
* means: only when konnekting is ready for appliction
*/
if (Konnekting.isReadyForApplication())
{
SerialUSB.print(hdc1080.readTemperature());
//Knx.write(COMOBJ_temperature,hdc1080.readTemperatu re());
delay(5000);
}
}

Code:

Arduino: 1.8.13 (Windows 10), Board: "Arduino Zero (Native USB Port)"
C:\Users\User\Documents\arduino-1.8.13\arduino-builder -dump-prefs -logger=machine -hardware C:\Users\User\Documents\arduino-1.8.13\hardware -hardware C:\Users\User\AppData\Local\Arduino15\packages -tools C:\Users\User\Documents\arduino-1.8.13\tools-builder -tools C:\Users\User\Documents\arduino-1.8.13\hardware\tools\avr -tools C:\Users\User\AppData\Local\Arduino15\packages -built-in-libraries C:\Users\User\Documents\arduino-1.8.13\libraries -libraries C:\Users\User\Documents\Arduino\libraries -fqbn=arduino:samd:arduino_zero_native -vid-pid=0000_0000 -ide-version=10813 -build-path C:\Users\User\AppData\Local\Temp\arduino_build_212 987 -warnings=default -build-cache C:\Users\User\AppData\Local\Temp\arduino_cache_964 954 -prefs=build.warn_data_percentage=75 -prefs=runtime.tools.CMSIS-Atmel.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\CMSIS-Atmel\1.2.0 -prefs=runtime.tools.CMSIS-Atmel-1.2.0.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\CMSIS-Atmel\1.2.0 -prefs=runtime.tools.arduinoOTA.path=C:\Users\User\ AppData\Local\Arduino15\packages\arduino\tools\ard uinoOTA\1.2.1 -prefs=runtime.tools.arduinoOTA-1.2.1.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\arduinoOTA\1.2.1 -prefs=runtime.tools.arm-none-eabi-gcc.path=C:\Users\User\AppData\Local\Arduino15\pac kages\arduino\tools\arm-none-eabi-gcc\7-2017q4 -prefs=runtime.tools.arm-none-eabi-gcc-7-2017q4.path=C:\Users\User\AppData\Local\Arduino15\ packages\arduino\tools\arm-none-eabi-gcc\7-2017q4 -prefs=runtime.tools.bossac.path=C:\Users\User\AppD ata\Local\Arduino15\packages\arduino\tools\bossac\ 1.7.0-arduino3 -prefs=runtime.tools.bossac-1.7.0-arduino3.path=C:\Users\User\AppData\Local\Arduino1 5\packages\arduino\tools\bossac\1.7.0-arduino3 -prefs=runtime.tools.openocd.path=C:\Users\User\App Data\Local\Arduino15\packages\arduino\tools\openoc d\0.10.0-arduino7 -prefs=runtime.tools.openocd-0.10.0-arduino7.path=C:\Users\User\AppData\Local\Arduino1 5\packages\arduino\tools\openocd\0.10.0-arduino7 -prefs=runtime.tools.CMSIS.path=C:\Users\User\AppDa ta\Local\Arduino15\packages\arduino\tools\CMSIS\4. 5.0 -prefs=runtime.tools.CMSIS-4.5.0.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\CMSIS\4.5.0 -verbose C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino
C:\Users\User\Documents\arduino-1.8.13\arduino-builder -compile -logger=machine -hardware C:\Users\User\Documents\arduino-1.8.13\hardware -hardware C:\Users\User\AppData\Local\Arduino15\packages -tools C:\Users\User\Documents\arduino-1.8.13\tools-builder -tools C:\Users\User\Documents\arduino-1.8.13\hardware\tools\avr -tools C:\Users\User\AppData\Local\Arduino15\packages -built-in-libraries C:\Users\User\Documents\arduino-1.8.13\libraries -libraries C:\Users\User\Documents\Arduino\libraries -fqbn=arduino:samd:arduino_zero_native -vid-pid=0000_0000 -ide-version=10813 -build-path C:\Users\User\AppData\Local\Temp\arduino_build_212 987 -warnings=default -build-cache C:\Users\User\AppData\Local\Temp\arduino_cache_964 954 -prefs=build.warn_data_percentage=75 -prefs=runtime.tools.CMSIS-Atmel.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\CMSIS-Atmel\1.2.0 -prefs=runtime.tools.CMSIS-Atmel-1.2.0.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\CMSIS-Atmel\1.2.0 -prefs=runtime.tools.arduinoOTA.path=C:\Users\User\ AppData\Local\Arduino15\packages\arduino\tools\ard uinoOTA\1.2.1 -prefs=runtime.tools.arduinoOTA-1.2.1.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\arduinoOTA\1.2.1 -prefs=runtime.tools.arm-none-eabi-gcc.path=C:\Users\User\AppData\Local\Arduino15\pac kages\arduino\tools\arm-none-eabi-gcc\7-2017q4 -prefs=runtime.tools.arm-none-eabi-gcc-7-2017q4.path=C:\Users\User\AppData\Local\Arduino15\ packages\arduino\tools\arm-none-eabi-gcc\7-2017q4 -prefs=runtime.tools.bossac.path=C:\Users\User\AppD ata\Local\Arduino15\packages\arduino\tools\bossac\ 1.7.0-arduino3 -prefs=runtime.tools.bossac-1.7.0-arduino3.path=C:\Users\User\AppData\Local\Arduino1 5\packages\arduino\tools\bossac\1.7.0-arduino3 -prefs=runtime.tools.openocd.path=C:\Users\User\App Data\Local\Arduino15\packages\arduino\tools\openoc d\0.10.0-arduino7 -prefs=runtime.tools.openocd-0.10.0-arduino7.path=C:\Users\User\AppData\Local\Arduino1 5\packages\arduino\tools\openocd\0.10.0-arduino7 -prefs=runtime.tools.CMSIS.path=C:\Users\User\AppDa ta\Local\Arduino15\packages\arduino\tools\CMSIS\4. 5.0 -prefs=runtime.tools.CMSIS-4.5.0.path=C:\Users\User\AppData\Local\Arduino15\p ackages\arduino\tools\CMSIS\4.5.0 -verbose C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino
Using board 'arduino_zero_native' from platform in folder: C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11
Using core 'arduino' from platform in folder: C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11
Detecting libraries used...
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-g++" -mcpu=cortex-m0plus -mthumb -c -g -Os -w -std=gnu++11 -ffunction-sections -fdata-sections -fno-threadsafe-statics -nostdlib --param max-inline-insns-single=500 -fno-rtti -fno-exceptions -w -x c++ -E -CC -DF_CPU=48000000L -DARDUINO=10813 -DARDUINO_SAMD_ZERO -DARDUINO_ARCH_SAMD -D__SAMD21G18A__ -DUSB_VID=0x2341 -DUSB_PID=0x804d -DUSBCON "-DUSB_MANUFACTURER=\"Arduino LLC\"" "-DUSB_PRODUCT=\"Arduino Zero\"" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS\\4.5.0/CMSIS/Include/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS-Atmel\\1.2.0/CMSIS/Device/ATMEL/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated-avr-comp" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\variants\\ar duino_zero" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\sketch\\knx_btn_temp_led.ino.cpp" -o nul -DARDUINO_LIB_DISCOVERY_PHASE
Alternatives for KonnektingDevice.h: [KONNEKTING_Device_Library@1.0.0-BETA4b]
ResolveLibrary(KonnektingDevice.h)
-> cUserdates: [KONNEKTING_Device_Library@1.0.0-BETA4b]
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-g++" -mcpu=cortex-m0plus -mthumb -c -g -Os -w -std=gnu++11 -ffunction-sections -fdata-sections -fno-threadsafe-statics -nostdlib --param max-inline-insns-single=500 -fno-rtti -fno-exceptions -w -x c++ -E -CC -DF_CPU=48000000L -DARDUINO=10813 -DARDUINO_SAMD_ZERO -DARDUINO_ARCH_SAMD -D__SAMD21G18A__ -DUSB_VID=0x2341 -DUSB_PID=0x804d -DUSBCON "-DUSB_MANUFACTURER=\"Arduino LLC\"" "-DUSB_PRODUCT=\"Arduino Zero\"" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS\\4.5.0/CMSIS/Include/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS-Atmel\\1.2.0/CMSIS/Device/ATMEL/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated-avr-comp" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\variants\\ar duino_zero" "-IC:\\Users\\User\\Documents\\Arduino\\libraries\\K ONNEKTING_Device_Library\\src" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\sketch\\knx_btn_temp_led.ino.cpp" -o nul -DARDUINO_LIB_DISCOVERY_PHASE
Alternatives for ClosedCube_HDC1080.h: [ClosedCube_HDC1080@1.3.2]
ResolveLibrary(ClosedCube_HDC1080.h)
-> cUserdates: [ClosedCube_HDC1080@1.3.2]
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-g++" -mcpu=cortex-m0plus -mthumb -c -g -Os -w -std=gnu++11 -ffunction-sections -fdata-sections -fno-threadsafe-statics -nostdlib --param max-inline-insns-single=500 -fno-rtti -fno-exceptions -w -x c++ -E -CC -DF_CPU=48000000L -DARDUINO=10813 -DARDUINO_SAMD_ZERO -DARDUINO_ARCH_SAMD -D__SAMD21G18A__ -DUSB_VID=0x2341 -DUSB_PID=0x804d -DUSBCON "-DUSB_MANUFACTURER=\"Arduino LLC\"" "-DUSB_PRODUCT=\"Arduino Zero\"" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS\\4.5.0/CMSIS/Include/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS-Atmel\\1.2.0/CMSIS/Device/ATMEL/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated-avr-comp" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\variants\\ar duino_zero" "-IC:\\Users\\User\\Documents\\Arduino\\libraries\\K ONNEKTING_Device_Library\\src" "-IC:\\Users\\User\\Documents\\Arduino\\libraries\\C losedCube_HDC1080\\src" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\sketch\\knx_btn_temp_led.ino.cpp" -o nul -DARDUINO_LIB_DISCOVERY_PHASE
Alternatives for Wire.h: [Wire@1.0]
ResolveLibrary(Wire.h)
-> cUserdates: [Wire@1.0]
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-g++" -mcpu=cortex-m0plus -mthumb -c -g -Os -w -std=gnu++11 -ffunction-sections -fdata-sections -fno-threadsafe-statics -nostdlib --param max-inline-insns-single=500 -fno-rtti -fno-exceptions -w -x c++ -E -CC -DF_CPU=48000000L -DARDUINO=10813 -DARDUINO_SAMD_ZERO -DARDUINO_ARCH_SAMD -D__SAMD21G18A__ -DUSB_VID=0x2341 -DUSB_PID=0x804d -DUSBCON "-DUSB_MANUFACTURER=\"Arduino LLC\"" "-DUSB_PRODUCT=\"Arduino Zero\"" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS\\4.5.0/CMSIS/Include/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS-Atmel\\1.2.0/CMSIS/Device/ATMEL/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated-avr-comp" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\variants\\ar duino_zero" "-IC:\\Users\\User\\Documents\\Arduino\\libraries\\K ONNEKTING_Device_Library\\src" "-IC:\\Users\\User\\Documents\\Arduino\\libraries\\C losedCube_HDC1080\\src" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\libraries\\W ire" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\sketch\\knx_btn_temp_led.ino.cpp" -o nul -DARDUINO_LIB_DISCOVERY_PHASE
Using cached library dependencies for file: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src\DebugUtil.cpp
Using cached library dependencies for file: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src\KnxComObject.cpp
Using cached library dependencies for file: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src\KnxDevice.cpp
Using cached library dependencies for file: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src\KnxTelegram.cpp
Using cached library dependencies for file: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src\KnxTpUart.cpp
Using cached library dependencies for file: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src\KonnektingDevice.cpp
Using cached library dependencies for file: C:\Users\User\Documents\Arduino\libraries\ClosedCu be_HDC1080\src\ClosedCube_HDC1080.cpp
Using cached library dependencies for file: C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\libraries\Wire\Wire.cpp
Generating function prototypes...
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-g++" -mcpu=cortex-m0plus -mthumb -c -g -Os -w -std=gnu++11 -ffunction-sections -fdata-sections -fno-threadsafe-statics -nostdlib --param max-inline-insns-single=500 -fno-rtti -fno-exceptions -w -x c++ -E -CC -DF_CPU=48000000L -DARDUINO=10813 -DARDUINO_SAMD_ZERO -DARDUINO_ARCH_SAMD -D__SAMD21G18A__ -DUSB_VID=0x2341 -DUSB_PID=0x804d -DUSBCON "-DUSB_MANUFACTURER=\"Arduino LLC\"" "-DUSB_PRODUCT=\"Arduino Zero\"" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS\\4.5.0/CMSIS/Include/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS-Atmel\\1.2.0/CMSIS/Device/ATMEL/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated-avr-comp" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\variants\\ar duino_zero" "-IC:\\Users\\User\\Documents\\Arduino\\libraries\\K ONNEKTING_Device_Library\\src" "-IC:\\Users\\User\\Documents\\Arduino\\libraries\\C losedCube_HDC1080\\src" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\libraries\\W ire" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\sketch\\knx_btn_temp_led.ino.cpp" -o "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\preproc\\ctags_target_for_gcc_minus_e. cpp" -DARDUINO_LIB_DISCOVERY_PHASE
"C:\\Users\\User\\Documents\\arduino-1.8.13\\tools-builder\\ctags\\5.8-arduino11/ctags" -u --language-force=c++ -f - --c++-kinds=svpf --fields=KSTtzns --line-directives "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\preproc\\ctags_target_for_gcc_minus_e. cpp"
Sketch wird kompiliert...
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-g++" -mcpu=cortex-m0plus -mthumb -c -g -Os -std=gnu++11 -ffunction-sections -fdata-sections -fno-threadsafe-statics -nostdlib --param max-inline-insns-single=500 -fno-rtti -fno-exceptions -MMD -DF_CPU=48000000L -DARDUINO=10813 -DARDUINO_SAMD_ZERO -DARDUINO_ARCH_SAMD -D__SAMD21G18A__ -DUSB_VID=0x2341 -DUSB_PID=0x804d -DUSBCON "-DUSB_MANUFACTURER=\"Arduino LLC\"" "-DUSB_PRODUCT=\"Arduino Zero\"" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS\\4.5.0/CMSIS/Include/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS-Atmel\\1.2.0/CMSIS/Device/ATMEL/" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no/api/deprecated-avr-comp" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\cores\\ardui no" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\variants\\ar duino_zero" "-IC:\\Users\\User\\Documents\\Arduino\\libraries\\K ONNEKTING_Device_Library\\src" "-IC:\\Users\\User\\Documents\\Arduino\\libraries\\C losedCube_HDC1080\\src" "-IC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\libraries\\W ire" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\sketch\\knx_btn_temp_led.ino.cpp" -o "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\sketch\\knx_btn_temp_led.ino.cpp.o"
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:79:32: warning: 'B00000000' is deprecated: use 0b00000000 instead [-Wdeprecated-declarations]
KNX_PRIORITY_SYSTEM_VALUE = B00000000,
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:45:3: note: declared here
B00000000 DEPRECATED(0b00000000) = 0,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:80:32: warning: 'B00000100' is deprecated: use 0b00000100 instead [-Wdeprecated-declarations]
KNX_PRIORITY_HIGH_VALUE = B00000100,
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:73:3: note: declared here
B00000100 DEPRECATED(0b00000100) = 4,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:81:32: warning: 'B00001000' is deprecated: use 0b00001000 instead [-Wdeprecated-declarations]
KNX_PRIORITY_ALARM_VALUE = B00001000,
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:96:3: note: declared here
B00001000 DEPRECATED(0b00001000) = 8,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:82:32: warning: 'B00001100' is deprecated: use 0b00001100 instead [-Wdeprecated-declarations]
KNX_PRIORITY_NORMAL_VALUE = B00001100
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:116:3: note: declared here
B00001100 DEPRECATED(0b00001100) = 12,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:86:32: warning: 'B00000000' is deprecated: use 0b00000000 instead [-Wdeprecated-declarations]
KNX_COMMAND_VALUE_READ = B00000000,
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:45:3: note: declared here
B00000000 DEPRECATED(0b00000000) = 0,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:87:32: warning: 'B00000001' is deprecated: use 0b00000001 instead [-Wdeprecated-declarations]
KNX_COMMAND_VALUE_RESPONSE = B00000001,
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:53:3: note: declared here
B00000001 DEPRECATED(0b00000001) = 1,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:88:32: warning: 'B00000010' is deprecated: use 0b00000010 instead [-Wdeprecated-declarations]
KNX_COMMAND_VALUE_WRITE = B00000010,
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:60:3: note: declared here
B00000010 DEPRECATED(0b00000010) = 2,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:89:32: warning: 'B00001010' is deprecated: use 0b00001010 instead [-Wdeprecated-declarations]
KNX_COMMAND_MEMORY_WRITE = B00001010
^~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:106:3: note: declared here
B00001010 DEPRECATED(0b00001010) = 10,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'void KnxTelegram::ChangePriority(e_KnxPriority)':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:98:45: warning: 'B00001100' is deprecated: use 0b00001100 instead [-Wdeprecated-declarations]
#define CONTROL_FIELD_PRIORITY_MASK B00001100
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:220:21: note: in expansion of macro 'CONTROL_FIELD_PRIORITY_MASK'
{ _controlField &= ~CONTROL_FIELD_PRIORITY_MASK; _controlField |= priority & CONTROL_FIELD_PRIORITY_MASK;}
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:116:3: note: declared here
B00001100 DEPRECATED(0b00001100) = 12,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:98:45: warning: 'B00001100' is deprecated: use 0b00001100 instead [-Wdeprecated-declarations]
#define CONTROL_FIELD_PRIORITY_MASK B00001100
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:220:78: note: in expansion of macro 'CONTROL_FIELD_PRIORITY_MASK'
{ _controlField &= ~CONTROL_FIELD_PRIORITY_MASK; _controlField |= priority & CONTROL_FIELD_PRIORITY_MASK;}
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:116:3: note: declared here
B00001100 DEPRECATED(0b00001100) = 12,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'e_KnxPriority KnxTelegram::GetPriority() const':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:98:45: warning: 'B00001100' is deprecated: use 0b00001100 instead [-Wdeprecated-declarations]
#define CONTROL_FIELD_PRIORITY_MASK B00001100
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:223:41: note: in expansion of macro 'CONTROL_FIELD_PRIORITY_MASK'
{return (e_KnxPriority)(_controlField & CONTROL_FIELD_PRIORITY_MASK);}
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:116:3: note: declared here
B00001100 DEPRECATED(0b00001100) = 12,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'void KnxTelegram::SetRepeated()':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:97:49: warning: 'B11011111' is deprecated: use 0b11011111 instead [-Wdeprecated-declarations]
#define CONTROL_FIELD_SET_REPEATED(x) (x&=B11011111)
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:226:3: note: in expansion of macro 'CONTROL_FIELD_SET_REPEATED'
{ CONTROL_FIELD_SET_REPEATED(_controlField);};
^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:515:3: note: declared here
B11011111 DEPRECATED(0b11011111) = 223,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'boolean KnxTelegram::IsRepeated() const':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:96:45: warning: 'B00100000' is deprecated: use 0b00100000 instead [-Wdeprecated-declarations]
#define CONTROL_FIELD_REPEATED_MASK B00100000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:229:22: note: in expansion of macro 'CONTROL_FIELD_REPEATED_MASK'
{if (_controlField & CONTROL_FIELD_REPEATED_MASK ) return false; else return true ; }
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:198:3: note: declared here
B00100000 DEPRECATED(0b00100000) = 32,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'boolean KnxTelegram::IsMulticast() const':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:104:48: warning: 'B10000000' is deprecated: use 0b10000000 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK B10000000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:252:21: note: in expansion of macro 'ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK'
{return (_routing & ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK);}
^
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:420:3: note: declared here
B10000000 DEPRECATED(0b10000000) = 128,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'void KnxTelegram::SetMulticast(boolean)':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:104:48: warning: 'B10000000' is deprecated: use 0b10000000 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK B10000000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:255:24: note: in expansion of macro 'ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK'
{ if (mode) _routing|= ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK;
^
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:420:3: note: declared here
B10000000 DEPRECATED(0b10000000) = 128,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:104:48: warning: 'B10000000' is deprecated: use 0b10000000 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK B10000000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:256:21: note: in expansion of macro 'ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK'
else _routing &= ~ROUTING_FIELD_TARGET_ADDRESS_TYPE_MASK; }
^
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:420:3: note: declared here
B10000000 DEPRECATED(0b10000000) = 128,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'void KnxTelegram::ChangeRoutingCounter(byte)':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:105:48: warning: 'B01110000' is deprecated: use 0b01110000 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_COUNTER_MASK B01110000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:259:31: note: in expansion of macro 'ROUTING_FIELD_COUNTER_MASK'
{ counter <<= 4; _routing &= ~ROUTING_FIELD_COUNTER_MASK; _routing |= (counter & ROUTING_FIELD_COUNTER_MASK); }
^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:389:3: note: declared here
B01110000 DEPRECATED(0b01110000) = 112,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:105:48: warning: 'B01110000' is deprecated: use 0b01110000 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_COUNTER_MASK B01110000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:259:82: note: in expansion of macro 'ROUTING_FIELD_COUNTER_MASK'
{ counter <<= 4; _routing &= ~ROUTING_FIELD_COUNTER_MASK; _routing |= (counter & ROUTING_FIELD_COUNTER_MASK); }
^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:389:3: note: declared here
B01110000 DEPRECATED(0b01110000) = 112,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'byte KnxTelegram::GetRoutingCounter() const':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:105:48: warning: 'B01110000' is deprecated: use 0b01110000 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_COUNTER_MASK B01110000
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:262:23: note: in expansion of macro 'ROUTING_FIELD_COUNTER_MASK'
{ return ((_routing & ROUTING_FIELD_COUNTER_MASK)>>4); }
^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:389:3: note: declared here
B01110000 DEPRECATED(0b01110000) = 112,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'void KnxTelegram::SetPayloadLength(byte)':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:106:48: warning: 'B00001111' is deprecated: use 0b00001111 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_PAYLOAD_LENGTH_MASK B00001111
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:265:15: note: in expansion of macro 'ROUTING_FIELD_PAYLOAD_LENGTH_MASK'
{ _routing&= ~ROUTING_FIELD_PAYLOAD_LENGTH_MASK ; _routing |= length & ROUTING_FIELD_PAYLOAD_LENGTH_MASK; }
^
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:131:3: note: declared here
B00001111 DEPRECATED(0b00001111) = 15,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:106:48: warning: 'B00001111' is deprecated: use 0b00001111 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_PAYLOAD_LENGTH_MASK B00001111
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:265:72: note: in expansion of macro 'ROUTING_FIELD_PAYLOAD_LENGTH_MASK'
{ _routing&= ~ROUTING_FIELD_PAYLOAD_LENGTH_MASK ; _routing |= length & ROUTING_FIELD_PAYLOAD_LENGTH_MASK; }
^
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:131:3: note: declared here
B00001111 DEPRECATED(0b00001111) = 15,
^~~~~~~~~
In file included from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.h:32:0,
from C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.h:32,
from C:\Users\User\Documents\Arduino\Tempsensor\knx_btn _temp_led\knx_btn_temp_led.ino:1:
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h: In member function 'byte KnxTelegram::GetPayloadLength() const':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:106:48: warning: 'B00001111' is deprecated: use 0b00001111 instead [-Wdeprecated-declarations]
#define ROUTING_FIELD_PAYLOAD_LENGTH_MASK B00001111
^
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxTelegram.h:268:21: note: in expansion of macro 'ROUTING_FIELD_PAYLOAD_LENGTH_MASK'
{return (_routing & ROUTING_FIELD_PAYLOAD_LENGTH_MASK);}
^
In file included from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/ArduinoAPI.h:26:0,
from C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/Arduino.h:23,
from C:\Users\User\AppData\Local\Temp\arduino_build_212 987\sketch\knx_btn_temp_led.ino.cpp:1:
C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\cores\arduino/api/Binary.h:131:3: note: declared here
B00001111 DEPRECATED(0b00001111) = 15,
^~~~~~~~~
Compiling libraries...
Compiling library "KONNEKTING_Device_Library"
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_212 987\libraries\KONNEKTING_Device_Library\DebugUtil. cpp.o
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_212 987\libraries\KONNEKTING_Device_Library\KnxTelegra m.cpp.o
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_212 987\libraries\KONNEKTING_Device_Library\KnxDevice. cpp.o
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_212 987\libraries\KONNEKTING_Device_Library\KnxComObje ct.cpp.o
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_212 987\libraries\KONNEKTING_Device_Library\KnxTpUart. cpp.o
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_212 987\libraries\KONNEKTING_Device_Library\Konnekting Device.cpp.o
Compiling library "ClosedCube_HDC1080"
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_212 987\libraries\ClosedCube_HDC1080\ClosedCube_HDC108 0.cpp.o
Compiling library "Wire"
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_212 987\libraries\Wire\Wire.cpp.o
Compiling core...
Zuvor kompilierte Datei wird verwendet: C:\Users\User\AppData\Local\Temp\arduino_build_212 987\core\variant.cpp.o
Using precompiled core: C:\Users\User\AppData\Local\Temp\arduino_cache_964 954\core\core_arduino_samd_arduino_zero_native_91e 273adf6e8ac7a10158c7ef2e10266.a
Linking everything together...
"C:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\arm-none-eabi-gcc\\7-2017q4/bin/arm-none-eabi-g++" "-LC:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987" -Os -Wl,--gc-sections -save-temps "-TC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\hardware\\samd\\1.8.11\\variants\\ar duino_zero/linker_scripts/gcc/flash_with_bootloader.ld" "-Wl,-Map,C:\\Users\\User\\AppData\\Local\\Temp\\arduino _build_212987/knx_btn_temp_led.ino.map" --specs=nano.specs --specs=nosys.specs -mcpu=cortex-m0plus -mthumb -Wl,--cref -Wl,--check-sections -Wl,--gc-sections -Wl,--unresolved-symbols=report-all -Wl,--warn-common -Wl,--warn-section-align -o "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987/knx_btn_temp_led.ino.elf" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\sketch\\knx_btn_temp_led.ino.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\libraries\\KONNEKTING_Device_Library\\ DebugUtil.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\libraries\\KONNEKTING_Device_Library\\ KnxComObject.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\libraries\\KONNEKTING_Device_Library\\ KnxDevice.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\libraries\\KONNEKTING_Device_Library\\ KnxTelegram.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\libraries\\KONNEKTING_Device_Library\\ KnxTpUart.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\libraries\\KONNEKTING_Device_Library\\ KonnektingDevice.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\libraries\\ClosedCube_HDC1080\\ClosedC ube_HDC1080.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\libraries\\Wire\\Wire.cpp.o" "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987\\core\\variant.cpp.o" -Wl,--start-group "-LC:\\Users\\User\\AppData\\Local\\Arduino15\\packa ges\\arduino\\tools\\CMSIS\\4.5.0/CMSIS/Lib/GCC/" -larm_cortexM0l_math -lm "C:\\Users\\User\\AppData\\Local\\Temp\\arduino_bu ild_212987/..\\arduino_cache_964954\\core\\core_arduino_samd_ arduino_zero_native_91e273adf6e8ac7a10158c7ef2e102 66.a" -Wl,--end-group
C:\Users\User\AppData\Local\Temp\arduino_build_212 987\libraries\KONNEKTING_Device_Library\KnxDevice. cpp.o: In function `KnxDevice::GetTpUartEvents(e_KnxTpUartEvent)':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.cpp:448: undefined reference to `knxEvents(unsigned char)'
C:\Users\User\AppData\Local\Temp\arduino_build_212 987\libraries\KONNEKTING_Device_Library\Konnekting Device.cpp.o: In function `konnektingKnxEvents(unsigned char)':
C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.cpp:92: undefined reference to `knxEvents(unsigned char)'
collect2.exe: error: ld returned 1 exit status
Bibliothek KONNEKTING_Device_Library in Version 1.0.0-BETA4b im Ordner: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library wird verwendet
Bibliothek ClosedCube_HDC1080 in Version 1.3.2 im Ordner: C:\Users\User\Documents\Arduino\libraries\ClosedCu be_HDC1080 wird verwendet
Bibliothek Wire in Version 1.0 im Ordner: C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\libraries\Wire wird verwendet
exit status 1
Fehler beim Kompilieren für das Board Arduino Zero (Native USB Port).

**Eugenius** · 26.12.2020, 19:24

Meinst du
B00001111 DEPRECATED(0b00001111) = 15,
?

Ignorieren...

**Freeman** · 26.12.2020, 19:31

//edit2 Fehler gefunden -> am Ende

Ne, das am Ende... da bricht der Compiler ab und lädt auch nicht hoch.

Code:

C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KnxDevice.cpp:448: undefined reference to `knxEvents(unsigned char)' C:\Users\User\AppData\Local\Temp\arduino_build_212 987\libraries\KONNEKTING_Device_Library\Konnekting Device.cpp.o: In function `konnektingKnxEvents(unsigned char)': C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library\src/KonnektingDevice.cpp:92: undefined reference to `knxEvents(unsigned char)'

collect2.exe: error: ld returned 1 exit status

Bibliothek KONNEKTING_Device_Library in Version 1.0.0-BETA4b im Ordner: C:\Users\User\Documents\Arduino\libraries\KONNEKTI NG_Device_Library wird verwendet Bibliothek ClosedCube_HDC1080 in Version 1.3.2 im Ordner: C:\Users\User\Documents\Arduino\libraries\ClosedCu be_HDC1080 wird verwendet Bibliothek Wire in Version 1.0 im Ordner: C:\Users\User\AppData\Local\Arduino15\packages\ard uino\hardware\samd\1.8.11\libraries\Wire wird verwendet

exit status 1 Fehler beim Kompilieren für das Board Arduino Zero (Native USB Port).

//edit

scheint irgendwas mit der Konnekting.init () zu tun zu haben. wenn ich die entferne klappts.
Ich guck jetzt mal nach den übergebenen Variablen/Konstanten... da hab ich eigentlich nichts verändert...

//edit2
Fehler gefunden, KnxEvents() Funktion nicht mitkopiert... muss mal durchsteigen, was ich mit der Funktion überhaupt machen muss^^

Ankündigung

Anfängerprobleme Temp/Hum Sensor

Kommentar

Kommentar

Kommentar

Kommentar

Kommentar

Kommentar

Kommentar

Kommentar

Kommentar

Kommentar

Kommentar

Kommentar

Kommentar

Kommentar

Kommentar