Ankündigung

Einklappen
Keine Ankündigung bisher.

Multi Interface (KNX, UART, I²C, SPI, 1wire ...)

Einklappen
X
 
  • Filter
  • Zeit
  • Anzeigen
Alles löschen
neue Beiträge

    first of all, IDs must be unique:
    https://github.com/fluppie/Temperatu...device.xml#L74
    In this line 15 and so on...
    Same here
    https://github.com/fluppie/Temperatu...config.xml#L73
    and other IDs


    This will not work:
    https://github.com/fluppie/Temperatu...ter/loop.h#L98
    I hope you have pressure more then 900

    values above 900 is a special error handling in HTU21D library (like, if lib retuerns 900, there is something went wrong).
    you can not use this values with BME680...
    Zuletzt geändert von Eugenius; 07.10.2019, 14:32.

    Kommentar


      Ok cool, did some changes and I have it working
      Working code: https://github.com/fluppie/Temperatu...or_BME680_1.0/

      Code:
      00:02:45.280 -> Start reading BME680
      00:02:45.657 -> Finished reading BME680
      00:02:45.657 -> currentTemp from BME read
      00:02:45.657 -> currentTemp: 22.15 C time: 176 ms
      00:02:45.657 -> currentHumd from BME read
      00:02:45.657 -> currentHumd: 60.66 % time: 0 ms
      00:02:45.657 -> currentPress from BME read
      00:02:45.657 -> currentPress: 1007.31 hPa time: 0 ms
      00:02:45.657 -> currentGas from BME read
      00:02:45.657 -> currentGas: 269.60 kOhm time: 0 ms
      00:03:15.267 -> Start reading BME680
      00:03:15.648 -> Finished reading BME680
      00:03:15.648 -> currentTemp from BME read
      00:03:15.648 -> currentTemp: 22.16 C time: 176 ms
      00:03:15.648 -> currentHumd from BME read
      00:03:15.648 -> currentHumd: 60.86 % time: 0 ms
      00:03:15.648 -> currentPress from BME read
      00:03:15.648 -> currentPress: 1007.33 hPa time: 0 ms
      00:03:15.648 -> currentGas from BME read
      00:03:15.648 -> currentGas: 273.63 kOhm time: 0 ms
      00:03:45.285 -> Start reading BME680
      00:03:45.666 -> Finished reading BME680
      00:03:45.666 -> currentTemp from BME read
      00:03:45.666 -> currentTemp: 22.16 C time: 176 ms
      00:03:45.666 -> currentHumd from BME read
      00:03:45.666 -> currentHumd: 60.85 % time: 0 ms
      00:03:45.666 -> currentPress from BME read
      00:03:45.666 -> currentPress: 1007.33 hPa time: 0 ms
      00:03:45.666 -> currentGas from BME read
      00:03:45.666 -> currentGas: 270.27 kOhm time: 1 ms
      Only the sensor read-out is between 377 and 381 ms according to the serial debug console. While Konnekting says 176ms ...
      And I think I found a bug when changing the GA's. Had 1/5/3, 1/5/4, 1/5/5 and 1/5/6 to start, changed it to 1/5/11, 1/5/12, 1/5/13 and 1/5/14. Reprogrammed it and it kept posting to 1/5/3 etc. Only when removing it from the KNX bus power it started posting with the new group addresses. Bug or by design?

      Kommentar


        After reprogramming, device will be resrarted. If not, something gone wrong

        Kommentar


          fluppie did you intentionally switch the thread? If not please continue your questions in the other thread or create a new one. Also at the other thread I suggested a change which will help you to get the real time.
          Zuletzt geändert von Sonnengruesser; 09.10.2019, 07:26.

          Kommentar


            No specific reason, thought not to "hijack" the BME280 thread. Eugenius, what do you like, seperate BME680 thread?

            Kommentar


              Yes, separate

              Kommentar

              Lädt...
              X